Question about Frigidaire ATF6000ES Front Load Washer

1 Answer

Unit does not work after power outage.

After a power outage the microwave does not operate other than the fan and light in the oven when the door is opened. The unit was unplugged and plugged in again as per the manual with no change. There is no response at the panel from any input on any buttons.

Posted by on

  • efpretty Dec 19, 2008

    After learning of my options I then consuted the net to determine the approximate cost of parts and I was able to determine whether or not to have the unit repaired. When I called a repair technician I was able to speak with him knowledgably.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Frigidaire Master
  • 19,396 Answers

That means that either the control board, or the magnetron inside the microwave had been damaged by the power surge.

Call a qualified technician for repair, or call the service number listed on the owner manual for factory repair or warranty services.

Posted on Dec 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

GE Front Load Washer has no power after a power outage. Main breaker has been reset and we have unplugged the unit from the wall. Door is still locked and no lights come on at all.


there could be a fuse in the control board that you can look at
other than that get in a technician as the unit could be damaged from the power surge

Jun 23, 2016 | GE Washing Machines

1 Answer

Where can I download a manual for Whirlpool AWM321


Hello,

You could go to whirlpool.com and click ower center and download a maual for your washer,i tried that but it says the model number couldn't be matched
The following is from the whirlpool website and it shows where to find the model#


Please find the type of appliance you are interested in and click on the link to view the likely location of the model number plate on that appliance here is where the model# could be found

Type of Appliance Model Number Plate Location Range Inside oven drawer, on oven rim Wall Oven Inside oven drawer, on rim Cooktop On underside of unit Microwave Inside microwave, on rim Dishwasher Inside dishwasher, on rim Refrigerator Inside refrigerator, on wall Trash Compactor Inside, on rim Food Waste Disposer Attached to the unit Washer Beneath washer lid, on tub rim Dryer Inside dryer door, on rim.

Jul 29, 2011 | Washing Machines

1 Answer

We load our machine and start it. After about two minutes it sends an error message door and stops operating even though the door is firmly shut. What is wrong and what can we do?


Sounds like the door switch or motherboard is faulty. Try testing the door switch by disconnecting and splicing the wires from door together to read as door being closed. If it still errors then you have a malfunctioning motherboard. I have seen malfunctioning units that were operating near certain elctronics, and or overhead lights, same happened with ovens near airports. Try keeping all other devices and lights off and test unit, sounds weird, but I have seen many weird instances.

Jun 15, 2010 | Washing Machines

1 Answer

F5 error on Whirlpool Accubake Range


1. If door latched:
a) Disconnect power from unit.
b) Check wires and connectors from control to door switch,
then from door switch to control. If no damage to wires
and all connectors okay, proceed to step c.
c) Replace door switch.
d) Re-apply power to unit and verify operations.
2. If door not latched:
a) Disconnect power from unit.
b) Check wires and connectors from control to latch switch,
then from latch switch to control. If no damage to wires
and all connectors okay, proceed to step c.
c) Repeat steps a) and b) for door switch.
3. Measure door switch (door open = switch open small low
voltage terminals).
4. Measure latch switch (unlatch = switch open. NOTE: Oven
light contacts are closed).
5. If corrections are made in any step, reconnect control to
verify correction.
6. Check door alignment.
7. If failure remains, replace control.

Dec 22, 2008 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

Power out when running. showed code F 71 now not working.


After power outage that will happen do this to fix.
Select PAUSE/CANCEL twice to cancel the cycle. Select
DRAIN & SPIN if there is excessive water in the washer.
Re-select cycle and press START. If the problem remains, call
for service.

Dec 17, 2008 | Kenmore Elite 45986 Front Load Washer

1 Answer

Random electrical problems, sometimes it works beautifully, sometimes not!


F11 = Communication between the Central Control Unit (CCU) and the
Motor Control Unit (MCU) cannot be sent correctly.
.
1. Unplug washer or disconnect power.
2. Check wire harness connections to the MCU, the motor, and
Central Control Unit (CCU).
3. Check the drive system for any worn or failed components.
4. Plug in washer or reconnect power.
5. Verify CCU operation by running a Diagnostic test or any
cycle.
6. Check the MCU by looking for operations of the drive motor.
7. Check the drive motor for powered rotations.
8. Check that the serial harness at the MCU is not mounted
upside down. The wires should be to the left when facing the
MCU connectors.

FDL=
A Door Lock Error occurs if the door cannot be locked. It will try to lock
it six times before displaying the error code.
Le code d’erreur “Verrouillage porte” apparaît s’il n’est pas possible de verrouiller la
porte. Le système effectue six tentatives de verrouillage avant d’afficher le code d’erreur.
■ Door lock mechanism is broken or removed from door.
■ Door switch/lock unit failure.
1. Unplug washer or disconnect power.
2. Check door switch/lock unit.
3. Check the wire harness connections to the door
switch/lock unit and Central Control Unit (CCU).

Feb 12, 2008 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Fridge stops working when power goes out.


It sounds like maybe the freezer fan is coming back on ??? Do you hear it in freezer?? I would recommend having it looked at ----this definately doesnt sound normal.

Jan 16, 2008 | Kenmore Elite 21082

1 Answer

Maytag washer not reset after power outage


The magnetic switch was stuck due to power outage / contactor are spark connect the contactor stuck together .Magnetic switch to replace.

Jan 09, 2008 | Maytag Atlantis MAV6000 Top Load Washer

Not finding what you are looking for?
Frigidaire ATF6000ES Front Load Washer Logo

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...