Daikin Heating & Cooling - Recent Questions, Troubleshooting & Support
Code u 4 - Daikin model Rxymq48mvju
U4 Is a communication error between indoor and outdoor units.
usually means one of the PC boards is faulty. If unit has been freshly installed check wiring between indoor and outdoor 1,2,3 are the same colours on both boards.
9/5/2021 6:47:53 PM •
Daikin...
•
Answered
on Sep 05, 2021
U3 code error
Daikin
VRV Systems reduces your energy consumption by optimising seasonal performance with efficient indoor and outdoor units, innovative technologies, and smart energy management controls. If you are looking best VRV Systems with great durability and comfort. Each VRV unit is equipped with signature VRV configurator. There is a software solution that simplifies easy configuration and commissioning. Your installer spends less time configuring the outdoor units and it's easy to customise the settings to your building's needs.
4/2/2019 5:30:56 AM •
Daikin...
•
Answered
on Apr 02, 2019
Idec inverter e3 problem
This is stating that there has been a high pressure error on this system.
This could be due to fan motor or air flow problems with the condensing unit, but it could also be an issue with the high pressure sensor or switch
12/2/2017 9:16:11 PM •
Daikin...
•
Answered
on Dec 02, 2017
Daikin brc2a71
This is a communication issue between the sub remote controller and the master remote controller.
This fault occurs when a remote controller that has been set to sub cannot see the master remote controller that has to be installed on the fan coil.
Please check the wiring for the remote controllers to ensure correct connections, also if there is only one remote on the unit ensure that the Main/Sub switch is set to Main.
WhAT DOES "iNTELLIGENT EYE" do?
The way I understand it, the 'eye' is just an infra red sensor that detects when someone is in the room. If it doesn't detect anyone, it reduces its power usage until someone walks back in and adjusts accordingly.
12/12/2015 11:44:43 AM •
Daikin...
•
Answered
on Dec 12, 2015
What does blinking light on wall unit mean?
If you have your Owner's manual, please check troubleshooting section. Should be a clue in there. It could mean filter needs to be changed, or possibly missing.
3/12/2015 12:09:37 PM •
Daikin...
•
Answered
on Mar 12, 2015
What does blinking light on wall unit mean?
When the Operation lamp is flashing, the unit can't operate efficiently and has shut off. Check and clean the Air Filters. Check that nothing is blocking the air inlet or outlets (on all indoor units (if a multi-unit system) and the outdoor unit). Remove all obstructions. Turn the breaker to Off and then On again. Check if the unit works with the remote.
If you have a multi-unit system, make sure that all indoor units are in the same Operation mode. If the units are on Auto, make sure that all units are set for Heat or Cool.
If the unit continues to have the Operation light flash, then you need to contact your service professional. The Operation manual for the FTXS18HVJU is available here: http://www.daikinac.com/content/assets/DOC/OperationManuals/FTXS15_18_24LVJU%20Operation%20Manual.pdf
I hope this helps.
Cindy Wells
3/12/2015 12:26:40 AM •
Daikin...
•
Answered
on Mar 12, 2015
Daikin fhyc140kve8
Outdoor unit will auto switch off when preset temp is reached, then switch on again auto as temp varies
Heat stops constantly
try changing pipesensor or thermostat they are most likley to go on a aircon let me know if it worked it should cause i had the same problem with mine till i changed the pipesensor and thermostat
ERROR CODE:UO
Insufficient gas. Need a tech to check for leaks, pressure test, evacuate and refill to correct levels.
Error message U4
Signal transmission error. Indoor and outdoor PCB's cannot communicate. Usually a faulty controller board in the outdoor unit. If the indoor unit otherwise functions normally (can control fan speed, louvres, beeps in replay to all remote buttons) then it is probably OK so check outdoor controller PCB.
Not finding what you are looking for?