Question about Refrigerators

1 Answer

Danby Refg PTC Starter

Where can I find this part

Posted by erovetto on


1 Answer


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 149 Answers

You can replace with an supco 3 n 1 for 1/3 1/4 (if run capacitor is used)

or use the combination relay/overload for 1/4 1/3(if there's no run capacitor)

if you need any additional help please e-mail @ [email protected]

Posted on Apr 29, 2008


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

BCFA27B need replacement for QP2-4.7. i think it's the starter.

Shop for Refrigerators need repla... on Google

Oasis 036056?001 R...
DrinkingFoun... Refrigerator Compressor S...
Sears Parts D... QP2?4.7 ' Danby Refrige...
Google Trusted StoreAppliance...
Danby QP2?4.7 Refrigerator St...
Google Trusted StoreSpeedy A... Oasis 036056?001...
PittsburghWat... Search Results

    uxcell 4.7 Ohm 1 Pin Refrigerator PTC Starter Relay Black, Inc.
    Rating: 4.8 - ‎63 reviews
    The original starting part QP2-4.7G is equivalent to this one. the 4.7G .... the PTC, so at this price, buy a spare because in year or two, you'll need another one. Questions And Answers: Will this replace a QP

Jan 01, 2016 | Refrigerators

1 Answer

Where can I purchase a starter for my VISSANI hvbc31st in the Dallas, Texas Area

Joe you probably wont find it locally in Dallas. I live in San Antonio and could not. Your best and cheapest bet is go to amazon and look up a single pin 4.7 ohm ptc. They have the exact replacement, but it comes from china so it will take a few weeks, but on the plus side it is only a couple of bucks.
For the more impatient and adventurous person like me you can also buy a similar designed 2 pin 22ohm ptc from amazon via prime shipping and get it in a few days. Open it up and take out the ceramic ohm disc and replace the broken one in the original one. Then wait for the right ones to come in from China. Black Plastic Housing 4 7 Ohm 1 Pin Refrigerator PTC Starter Relay

Nov 07, 2014 | Refrigerators

1 Answer

Frig wont get cold starter over load is clicking

first, remove ptc overload/relay (starter) off the compressor,then check compressor terminals on compressor by taking an ohm-meter and checking the terminals for resistance first one meter to the single terminal and one lead to each of the other terminals one at a time, then the meter leads between the two terminals there will be about 5 to 11 ohms on the first readings and a combined resistance on the second reading,then one lead to the compressors metal case and the other lead to each terminal there should be no resistance at all,if the readings are in line then simply replace the starter ptc

Nov 04, 2012 | Maytag Refrigerators

1 Answer

My fidge is a kenmore medel 25357685790 my starter ptc looks to be burnt so i decided to replace it but it includes three pieces the capacitor, starter ptc and overload. the new parts only have a diffrent...

I use ERP 410 (relay capacitor and overload) Get it at your local Appliance Parts Store
Very easy to install
Leo Ponder
Please vote for me if this helps.

Aug 02, 2011 | Refrigerators

1 Answer

Compressor is short,Model FF 350.This is 350 lt.double door frost free fridge.Compresser needs to be replaced,It is bought in April 2003

If you have had recent power failures, OFTEN the PTC motor starter for the compressor gets fried. The part can cost $50 or if you shop online as low as $2. What happens is if power briefly goes off and compressor has been running, the pressure is built up and when pwoer comes right back on, the PTC starter cannot start the compressor under pressure. Usually the compressor will get hot and just hum. The PTC unit is in a box that plugs on the side of the compressor. There is a capacitor that survives this and if you reuse that, you can get just the PTC part for less than $2.

The PTC is a little disk about the size of a quarter and fourr times as thick. It comes in a plastic box that the capacitor plugs onto and the whole thing then plugs onto the compressor.

Feb 11, 2011 | Air Tools & Compressors

1 Answer

Danby dkc645bls cools once, then wont kick back on when it starts getting warm.

Your compressor is not starting and in your case you have a thermal induced problem.

I looked for about an hour for parts below on-line with little success. (Danby sourced)

You have 3 possibilites as far as what is causing your problem.

1. PTC start relay / Klixon (2 parts as an assy)
2. Run capacitor

These are not expensive parts even if you ordered all of them.

The sad thing about it is the parts are probably available at your "local" appliance parts store.

If you can look at your compressors' label and copy down the
Manufacturer (i.e Embraco, Mitsubishi Elec, Panasonic etc) and ALL numbers (including LRA)
you can take that info to the local appliance parts supply and walk out with the parts in hand.

Otherwise your looking at calling Danby (number below) and telling them you need a PTC Start relay / Overload and run capacitor.

1-800-263-2629 (US)

Thanks for using FixYa

Oct 16, 2009 | Danby DKC645BLS Compact Beverage Cooler

1 Answer

Haier aficionado model AES44BPG compressor wont stay on


I had the same problem. Mine turned out to be the PTC starter. Checked the compressor coil resistance and it ws fine. Replaced the PTC starter with Item #: 1268268 from and it started right up. The PTC starter was an exact replacement.

Hope this helps some else trying to solve this problem. To bad Haier doesn't offer this part!!

May 01, 2009 | Haier (B000194UBA) Compact Refrigerator

1 Answer

Buzzing sound and not cooling

it looks like you have a bad compressor. try replacing the ptc starter and the run capacitor, if it did not change anything, then you have a bad compressort that needs to be replaced. if those parts are expensive, test the capacitor by using an analog meter, test the terminal using the X100 resistance. the meter needle should indicate continuity and slowly goes back to infinity. then reverse the terminals to the test prods and it should happen again. then test the resistance of the ptc starter, it should have a reading between 20 ohms and 100 ohms. and there whould be no rattling sound inside the ptc starter. hope i was able to help...

Feb 12, 2008 | Frigidaire GLRS237ZA Side by Side...

Not finding what you are looking for?
Refrigerators Logo

Related Topics:

465 people viewed this question

Ask a Question

Usually answered in minutes!

Top Refrigerators Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers


Level 3 Expert

85239 Answers

john h

Level 3 Expert

23424 Answers

Are you a Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides