When i press tuner to listen to the radio I can't ever get a radio station. It is always static, help please

Radio With Manual Tuning - Alibaba

www.alibaba.com > Automobiles & Motorcycles > radio > radio with

Radio With Manual Tuning, Buy Various High Quality Radio With Manual TuningProducts from Global Radio With Manual Tuning Suppliers and Radio With ...

Help Guide ' Tuning in an FM radio station manually ... - Sony

https://www.sony.co.uk/.../emanual/.../TP0000016777....

Sony CorporationThe headphone cord of headphones is an FM antenna, therefore, connect headphones to the (headphone) jack when listening to the FM radio.

Tuner (radio) - Wikipedia, the free encyclopedia

https://en.wikipedia.org/wiki/Tuner_(radio)

WikipediaA tuner is a subsystem that receives radio frequency (RF) transmissions like radio ...Older models would realize manual tuning by means of mechanically ...

[PDF]Tuning into a Radio Station - Onkyo

Not very specific. Do you have the manual?

The following is from a VSX-03TXH manual. It ain't pretty but it may help.

I'm posting it in multiple parts due to space contraints.

37

Chapter 6:

Using the tuner

Listening to the radio

The following steps show you how to tune in to FM and

AM radio broadcasts using the automatic (search) and

manual (step) tuning functions. If you already know the

frequency of the station you want, see Tuning directly to a

station below. Once you are tuned to a station you can

memorize the frequency for recall later-see Saving

station presets below for more on how to do this.

1 Press the FM/AM button to select the tuner.

2 Use the FM/AM button to change the band (FM or

AM), if necessary.

Each press switches the band between FM and AM.

3 Tune to a station.

There are three ways to do this:

Automatic tuning

To search for stations in the currently selected band,

press and hold TUNE ?©/?? for about a second. The

receiver will start searching for the next station,

stopping when it has found one. Repeat to search for

other stations.

Manual tuning

To change the frequency one step at a time, press

TUNE ?©/??.

High speed tuning

Press and hold TUNE ?©/?? for high speed tuning.

Release the button at the frequency you want.

Improving FM stereo sound

If the TUNED or STEREO indicators don't light when

tuning to an FM station because the signal is weak, press

the MPX button to switch the receiver into mono

reception mode. This should improve the sound quality

and allow you to enjoy the broadcast.

Using Neural THX

This feature uses Neural Surround™, THX® technology to

achieve optimal surround sound from FM radio.

• While listening to FM radio, press AUTO/DIRECT for
Neural THX listening.

FM reception is good; however there is a lot of static on AM 1000. No problems on other AM stations. Any suggestions or than stop listening to "1000"?

Owner's Manual is PN 3834RH0020U
On pg13
1. Press TUNER/BAND to select AM or FM
(Leftmost rectangular button on left of volume knob)
2. Select station by using TUNING +/-
3. Press PROGRAM/MEMO on the remote
A preset number will appear.
4. Press PRESET +/- (or PRESET ^/v on remote) to
select the preset number you want.
5. Press PROGRAM/MEMO again. The statio is stored.
6. Repeat above for more stations.

Believe you can store up to 30 stations.
Stations on presets 1, 2 and 3 take longer to 'kick in' when listening to the radio
as they are the 'tens' prefix for the preset numbers. 4 - 9 'kick in' immediately.

No, it should work, although it will depend on how good your reception is. This depends on how strong the signal is where you are trying to receive. If you have tried scanning for channels and all you receive is static, it's possible your tuner is bad. Have you tried to tune it to a known good station manusally?

replace Bad Circuit Dsp Pcb the rca part number is #265973

Press Function button at front of unit until display shows Tuner, and press Preset + / Preset -
If you want to listen Non-Preset stations, press << / >> keys of remote to tune a station. That's the procedure.
If built-in remote in your mobile have above said << / >> keys, you can tune station frequency.

Make sure your receiver is hooked up to proper AM and FM antennae. Try switching to AM, scan stations. If you hear AM static and/or weak signals the problem could be antennas are not hooked up. FM has AFT which blocks out weak or noisey stations and you wont hear anything without ant.

I would be willing to bet you have a 8v regulator circuit failure in hideaway Box. I have seen many of these units where a resistor opens and causes 12v instead of 8v to appear at tuner and a few other IC's. Usually But not always destroys tuner.
[email protected] if there are questions

buy a new antenna old one is worn out