PASSWORD PROBLEM TRIED TO PUT PASSWORD IN HAVIN PROBLEMS ,NOW CANT CONNECT TO WIRELESS ,HOW DO I RESET THE UNIT

Check the label under or at the back of the router for the default user name and password.. If you can't connect with this information try a reset ... hold the reset button in for 30 seconds to attempt a reset. If unsuccessful try again but also hold the button in while unplugging and reconnecting the AC adaptor at the back of the unit. If it still fails to reset after trying this a few times the unit may have a hardware failure.

Yes. If you change the password of the wireless network then other 2 units will get disconnected from wireless network (if they are connected to the wireless network. If these 2 units are wired to the router then it does not make any change)
I will suggest you to change the wireless network name also if you are changing the wireless network password.
Try to connect to the new wireless network on all the computers and devices.
Linksys router how to

If yuor first laptop is able to connect then try installing SIW on it and click the PASSWORDS link to see if it will retrieve the wireless password off the first laptop.
If not, and you cannot get into the router either, you will need to reset the netgear to factory by depressing the reset button in the back for 10 seconds, which resets the login to 'admin' and the password to 'password' to allow access to the router, and setting the wireless security to NONE - allowing you to change it to something you can remember.

If you are able to get into the router, but simply cannot remember the wireless password, you can reset it to something else without resetting the router through the wireless security menu in the router. You will need to then set both laptops to use the new password.

try to do this rest password on the router is u have to put in 0 26 times to reset the password typical problem of that kind of router try that and let me know leave a rating thanks.-natefixit

This is going to be the password that you setup your router with. If you cant remember the password you can reset your router and put in a new password.

you will be havin a wep or wpa security for wireless connection..type in that correctly..if u had forgotten it then connect ur laptop hardwire to ur router and configure router setting...type in 192.168.1.1 in ur browser address bar..ur router page will open..generally, by default password for router page will be "admin" or "password".. username will be "admin"...if u hav any issues then get back to me..

To restore the factory default configuration settings without knowing the administration password or IP address, you must use the Default Reset button on the rear panel of the router. 1. Press and hold the Default Reset button until the power light blinks on (about 10 seconds). 2. Release the Default Reset button and wait for the router to reboot. If the wireless router fails to restart or the power light continues to blink or turns solid amber, the unit may be defective. If the error persists, you might have a hardware problem and should contact technical support.

go to router settings as admin and select wireless settings->security. There you will find the WEP key written. Either note it down or change it to something that you can remember. And save.

first need to reset your router push the reset button at the back of the router for for 10 sec. then open internet explorer type 192.1681.1. enter type password admin enter ,..configure again your router enter the IP address. , Subnet mask , and DNS put the setting Static IP ,next click mac address clone and click "clone your pc mac" then click wireless at wireless network mode put it mix, at wireless channel put to the highest ghz. then after that check your line by trying to conect to the other pc using your UTP cable if it is working connect it again to your laptop

Try the following to reset it to the factory defaults.

Warning! This will reset all the settings in the router! Including any custom setup stuff, like WPA key, etc.

Turn the router on. Press and hold the reset button on it for 30 seconds. The reset button is usually a small recessed button on the back of the unit depending on which model you have.

Now you should be able to connect to it through your browser at http://192.168.1.1. Depending on your model, the username is blank and the password is "admin" (without the quotes) OR both username & password are "admin". Note that you will need to connect your computer to the router with a network cable to go through the setup process - you can't do it wirelessly.