Samsung tv picture moved to right hand side

To whom it may concern,

At the top right hand side of your remote press the "tv" button, then underneath that is an "input" button. Press this slowly until you find picture.

If this doesn't work, look on the side of the tv for a button labeled "input" or "source". Keep pressing that until you find picture, as an alternative to using the remote.

dish guy

If you need further help, I’m available over the phone at https://www.6ya.com/expert/brian_142c5ec89a7a3fda

This is a simple remote problem. It is the picture option. Just make sure your remote is on TV and press help. It should turn that screen on and off

your cable box is probably turned off.
Verify the cable box is turned on then press source until you get your picture back

Reset your cable or sat box....check connections....

On the right hand side of this television there are panel buttons. It appears that your son in law knocked the tv out of the correct input. Press the input button in order to cycle through the 5 inputs. Typically pressing the input button on the side panel of a television and pressing it again and again and again will make it change inputs. Universally the buttons on the tv panel function as follows: Channel up moves the cursor up. Channel down moves the cursor down. Volume + moves the cursor right. Volume - moves the cursor left.
Hope this helps

Moved my TV to another satellite receiver.
I received picture & audio.
Then I moved the TV back to its original position.

Now it works OK.

I probably hit a button that shut off my picture & sound.

I am mystified.

Thanks anyway.
Gerry............................;-))

Easy peezy...just press TV on your sky remote,now hold select and the red button until it blinks twice,after it blinks twice enter this code ...1430....it sjould blink twice again,now press standby,it should turn your tv of,if it does press select to save these settings,it should now control your volume too,let me know if this helps

your picture tubes is going bad. i've had 5 yes 5 of these tv's replaced by samsung/bestbuy. i've kept buying the PSP (product Service plan) now my most recent tv is doing the same. samsung no longer makes the picture tube for this model. i've already called them. it was a nice tv. i've gotten about 6 months out of each model. I'm moving on the LCD, nice rca 32 inch HDtv model at walmart for less than 500.00.

You can adjust the lines and make them straight. You can also in the same process, make them line up.
1. With the TV on, press the mute button the remote control so that you have picture but no sound.
2. With remote in one hand (holding it as far from the TV as you can but still be able to reach the TV with your other hand), press and hold the mute button again, with the other hand, using the control panel underneath the screen, press the menu button on the TV set.
You will notice an "S" on the screen on the right hand side about 2/3 from the left, halfway up the screen (If you did this right).
This means you are in service mode.
With the remote, curse right only once and you will have some information displayed in the upper left. The top line is Item, the one underneath is Data.
Press "7." This will display the built in cross hatch pattern. You can move the line around with the directional circle located at the center of the remote. Using the "3" button, you can decide which color to move. To move the curser to a new location, The number pad doubles as a direction key pad. (2-up), (4-left), (6-right), (8-down). To simplify the process, you can eliminate the red or blue or green lines and only focus on one color at a time. "0" will shut on/off the green line. "100 button" will shut on/off the red line. "CH RTN or Enter will shut on/off the blue line.
"7" will exit the process as well as get you there.
Power off when you are done and turn back on.
Repeat as needed.

To adjust manual convergence on your projection TV, follow theses steps:

1. Turn your TV on.
2. Let it warm up for 30 minutes.
3. Press the Menu button on your remote. The Main menu appears.
4. Use your remote to select Function, and then press the joystick.
5. Select Convergence, and then press the joystick. The Manual Convergence screen appears.
6. Select Red, and then press the joystick. A series of crosshairs appears on the screen.
7. Select one of the outside crosshairs by moving the joystick up/down/right/left or by pressing the 2 (up), 4 (left), 6 (right), or 8 (down) buttons on your remote. The method you use depends on the model of remote you have. Note: You must do the outside crosshairs first.
   

1. In the crosshair you selected, if you can see a horizontal red line, use the CH up or CH down buttons to move the line so that it is superimposed on the horizontal center line of the crosshair. Note: Make the single horizontal line as white as possible.
   

1. In the crosshair you selected, if you can see a vertical red line, use the Vol + or Vol - buttons to move the line so that it is superimposed on the vertical center line of the crosshair. Note: Make the single vertical line as white as possible.
   

1. Repeat for all outside crosshairs, and then for the inside crosshair.
2. Return to the Manual Convergence Screen, and select Blue, and then press the joystick.
3. Repeat Steps 7 through 10 for Blue.
4. Press the Menu button on your remote to exit.

Important: The directions above work for most Samsung Rear Projection TVs. Yours may be different. For exact directions to perform manual convergence, see your user's manual. If you don't have your user's manual on hand, click HERE to view your manual on line.
If you cannot get your Projection TV to converge, it may need to be serviced. To arrange a service appointment, call Samsung Customer Care at 1-800-Samsung (1-800-726-7864). Have your TV's model number and serial number on hand when you call.