I need help my oven has error code f09

We notice on this site that using the self cleaning cycle with break ovens about 50% of the time. Heating to 650 - 700'F is just too hostile to door locks, elements, fans and electronics boards.

You can't clear the F96 code, you have to fix the broken part. Start by disconnecting the power overnight by way of a reset. Then try testing the door lock with a test meter.

This code usually means that there is an issue with the upper cooling fan circuit or there is an obstruction in the cooling fan. ... This code usually means that a component has failed somewhere in the door lock circuit. F96. This code usually means that an internal component needs to be replaced.

Range & Wall Oven - Oven Error, Fault or Function Codes

There is a video here that might be useful

https://www.google.com/search?q=frigidaire+2+f96+error+code

Ultimately, you may need a service call, or because of age, invest in a new stove. Good luck though.

WHIRLPOOL
Range/Stove Oven Fault Codes, Common Failure
Code Condition Check/Repair Digit Failure Code2 F1 Analog to Digital Failure Disconnect for 30 seconds - if display reappears - replace control board F1 Safety flip flop Replace board F1 Shorted keypad Replace keypad F3 Oven temperature sensor opened Replace oven temperature sensor F2 Oven temperature sensor shorted Replace oven temperature sensor F3 Oven too hot Replace oven temperature sensor F3 Clean temp too hot Replace oven temperature sensor F5 Check door/latch switch Replace switch if defective

Your mfg knows how to do the deed short of using plastic explosives. Go to their web site for solution.

Hello there and thank you for choosing fixya
These codes normally show up during the cleaning cycle this is due to the extreem heat used during the self clean operation
Now to fix this is not too hard providing the sensor for the temperature has not been damaged due to the heat
Unplug the oven and leave it sit for 1 hour and do not touch there is a internal reset feature on these ovens that take 1 hour to reset once the hour is up plug in the oven and you may hear a audiable click sound or a buzz sound if so great then all you have to do is to press the cancel or off button then after 5 min attempt to unlock the door
if it does unlock and one of these error codes are still showing this means the the controle panel has suffered some damage and needs to be replace
I have seen brand new ovens have the controle panel fail after the first self clean operation because the parts inside of it fail due to the extreem heat ok?
Hope this helps
Best regards Michael

Self clean is hard on controls. I do not recommend self clean. Kills expensive parts. If the temp goes above 300 in the control panel, a control panel fuse will melt, killing the power to the control.
It looks like this:


Service manual for late model whirlpool double oven and some more interesting oven stuff



If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

HI. This code is a good indication of a separated key pad ribbon or the actual key pad may be damaged. Use the procedure below to isolate the culprit.

1. Check keypad connector for firm connection (keypad connects to control board).
2. Press CANCEL. If error code returns after 60 seconds, replace keypad (also called touch pad or membrane switch). Some models incorporate keypad in to control board as one unit. In this case, replace control board (also called ERC or clock).

Probably a bad door lock solenoid. That is some kind of door lock problem. Trouble is they are not all the same. This training manual shows locations of model number. Perhaps if you post that I might can come up with a tech sheet and you would get a better answer. see page 4

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Hi, Before you go working too hard to get you oven to go intothe self clean mode(self destruct)....check out this tip...

Self Cleaning Oven Problem


heatman101

" Wish I had read this first. I never would have used the self cleaningoption. Thanks for the info!!

utut

F1-E1 - EEPROM Checksum Error - Disconnect power for at least 30 seconds and then reconnect.
Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question
$$$$

F93 error code means Maximum oven door lock time exceeded. Check oven door lock/door lock switchs.hope this helps