Lexmark X1290 All-In-One InkJet Printer - Page 4 - Answered Questions & Fixed issues

10N0016 Ink Cartridge black 16ml





10N0026 Ink Cartridge 3-colour 3x5ml

Some cartridges have a natural hole in the top to screw into and make bigger, and you inject the ink here. Others you have to actually physically gently cut the top off (using a very sharp and very thin blade, i use a craft exchangeable blade kit like a pen knife) adn some just lift off. My lexmark 27 has to be sliced apart then lifts off after seal is broken. Then the ink is injected directly into the sponge areas inside as pamphlet instructs. Can you please tell me exactly what the cd said in short, to further help. Some cartridges have a ruber bung to refil into as well.

yes simple answer but yes if you know how to do it then your fine.

please rate my help to you.
thank you.

You can download the drivers from Lexmark's website here.

regards,
Bob Headrick, MS MVP Printing/Imaging

If you do not have the disk you must download the software from Internet, follow instructions below,

Click here:Official Lexmark Drivers and Software

A web page will open, follow instructions, select model, select operative system etc., and click on download .
Chose to download the file in my documents when asked.
After downloading, find the file,double click on the file ,then if you get in troubles, follow the instructions below to reset and reinstall drivers:

• Unplug printer USB.
• Go to control panel >> installed printers in Windows and remove (delete ) any installed printer from printer list.
• Download driver from website, or use the disk and run the install file.
  
• Follow driver installation wizard.
• Plug back printer when prompted from installation wizard.

Note:some printerdoes not work on Vista

[email protected] that is my email add.i give you a driver there..see you..

Download the free printer driver from Lexmark web site.

Fond this on the Lexmark Website. Hope it helps.

Attention Windows Vista Users
If you have installed your printer on your PC using an original Lexmark Driver CD that came with your product and you are experiencing problems when printing, you may have installed the Windows XP driver.

Follow these steps to resolve:
· 1) Disconnect your USB cable from your printer.
· 2) Uninstall all Lexmark printer drivers on your PC.
· 3) Download the correct Vista driver for your model.
· 4) While leaving the USB unconnected, Install the driver on your PC.

Important - Do not reconnect the USB cable until the install software prompts the question of how the printer is connected.

Hi,
Here's a link to the driver software that is on the cd:
http://driverscollection.com/?file_cid=39869124438cff00d7dd102c3f4

Unzip to a folder. Plug in the printer and go to Control Panel, System, Device Manager and under Printers or Unknown Device, double click the device and click the driver tab and install the driver. Choose the 'Let me choose the driver' type option and navigate to the folder you unzipped it to, install and reboot.

Hope this helps

Chris (ziraffa)

Here's the user's guide =>

http://www.lexmark.com/publications/pdfs/1200/eng/ug.pdf

Faxing is on page 12. Troubleshooting is on page 16.

Good Luck!

please reinstall the printer drivers 

Sometimes I have found you need to adjust the screen bar at the bottom

Hello,
If you dont have the manufacturer CD, you should be able to get the drivers here. Just enter x1250 in the Search by printer model field and press Enter. Click the Download Driver link and choose your operating system in the Select Windows field. Then on the next page, choose the Download Now link on the right. On the next page you may see a yellow security banner at the top of the browser. If so, click it and choose Download File. After that, choose Save to start the download. After the download completes you can double click the file to start the installation.

Hope this helps. Please remember to rate this information.

Thanks

http://driverscollection.com/?H=X1290&By=Lexmark

here sir you can download here the driver and install in your computer.

http://www.lexmark.com/lexmark/sequentialem/home/0,6959,204816596_1019285789_0_en,00.html

CHARCOIS

quero um dowlod pra instalar no meu computador...

I would start over. Delete the print jobs from the queue, then uninstall the printer software. Install it again from the CD and try again.

Steve

I bought a Lexmark X1290 printer and installed a wrong driver (for WinXP) from the enclosed CD. Then I could not run the All in One program. After many reinstallation attemps, I finally found a solution (which is unfortunately quite hidden at the Lexmark website):

1) Unplug the printer's USB cable from the computer.
2) Download the cleaning utility from ftp://ftp.lexmark.com/driver/inkjet_drivers/Cleanup/.
3) Double-click on the cleanup utility and follow the on-screen instructions to run it.
4) Restart the computer.
5) Download all files from ftp://ftp.lexmark.com/driver/inkjet_drivers/Cleanup/reg/
6) Follow the instructions in the "Vista BackDoor Instructions.txt" and delete all remaining Lexmark
keys in the registry.
7) Restart the computer
8) Download a proper driver for Windows Vista from the Lexmark website.
9) Install the driver accordingly to the instructions (it's important to plug the printer's USB cable when you are ask to, not before)

The problem with Lexmark Unistall and CleanUp Utility is that you cannot delete all Lexmark registry keys while you arelogged in the system. This is anellegant way how to circumvent the problem.

See if you can start a scan from your computer. In your Start->All Programs->Lexmark 1200 Series folder, there should be the All-In-One Center or the Productivity Studio or some such software. You should be able to start a scan from there.

Steve

Go to www.lexmark.com and click on DRIVERS AND DOWNLOADS. Then use the DRIVER FINDER. In SEARCH BY MODEL, type in 1290 and you can choose a driver from there.

Steve