20 Most Recent Whirlpool GR460 Electric Kitchen Range - Page 4 Questions & Answers

The F9 error code on a Whirlpool stove typically indicates a problem with the oven temperature sensor. The oven temperature sensor is a device that measures the temperature inside the oven and sends this information to the control board. If the sensor is not functioning properly, it can cause the control board to display the F9 error code.

To troubleshoot the problem, you can try the following steps:

Check the oven temperature sensor: Make sure the sensor is securely connected to the control board and not damaged. You can also check the resistance of the sensor using a multimeter to see if it is within the specified range.

Check the wiring: Make sure all the wiring for the oven temperature sensor is securely connected and not damaged. Check for any frayed or damaged wires, and repair or replace them as needed.

Check the control board: If the oven temperature sensor and wiring are in good condition, the problem may be with the control board. You can try resetting the control board by unplugging the stove and waiting a few minutes before plugging it back in.

If these steps do not resolve the issue, you may need to take the stove to a professional appliance repair shop for further evaluation and repair. They will be able to diagnose the problem and recommend the necessary repairs.

The fuse is your breaker. There may be a fuse hiding under the control board display but unlikely. It is likely to be the control panel itself. I would suggest dealer service as they are expensive, need correct diagnosis and warranty on the part and the replacement labour.

All Gas Ovens can be fixed, but the should be serviced by a registered gas technician. The spark igniter is only one part of the lighting procedure, they also have a thermocouple, which is a safety device that open the main gas valve once certainly criteria are met usually a pilot light flame. The parts schematic shows the gas valve and it is $181. I don't see a safety thermocouple. https://www.searspartsdirect.com/model/2v56d5n3jv-001198/whirlpool-sf362lxss0-gas-range-parts This is the part that is likely to have failed, but I am reluctant to suggest you change it on my say so. Pay the extra $75 for a qualified technician to diagnose and replace. It has electrical contacts, so the fail safe is probably inside and is dependent on the spark igniter being fully functional. https://www.searspartsdirect.com/product/5w6dsrlw7b-0022-664/id-9761959 ..

normally on inside electrical cover

1990 the 46th week (November)

Whirlpool Date Codes - Electrical-Forensics

https://www.electrical-forensics.com > MajorAppliances Whirlpool Appliances and Date Codes: How to to determine when your Whirlpool Appliance was manufactured from its serial number and model number.

You should be able to pull the knob straight out. Don't lose the internal sleeve. Here is a quick DIY video. https://www.youtube.com/watch?v=NSChe0uwRvA Or you can put some Loctite glue in the cracks on both sides before you tighten the zip Just to strenghten this in case it gets bumped again.

time to replace it with new model

if range uses electric.check fuses,and reset breaker.make sure proper voltage is going to the range.

use your tape measure

call your local gas appliance repair service .warranty was 1 year unless you bought and extended one

sad to say it but with a large family to feed perhaps a new stove is needed buying used is never the best choice

look for their secret hidden fastener

Check position / alignment of flame to gas line

Need a conversion kit can't just hook up a tank and turn on

F8E0 Cooling Fan Speed Too Low Fan speed below 500 rpm, either because the fan is spinning too slowly or because there is a problem with the Hall Effect sensor. When will occur: Within 20 seconds of a fault condition when cavity temperature is above 170°F (77°C). RECOMMENDED CORRECTIVE ACTION PROCEDURE 1.Unplug range or disconnect power. 2.Pull the range forward and remove the top access cover. 3.Verify there are no obstructions in the blower. If there is an obstruction, remove it and go to Step 6. If no obstructions, go to Step 4. 4.Disconnect control board connect or P5 and check the fan motor for 105? resistance between P5-1 and P6-3. If the motor test is not good, replace motor and go to Step 6. If motor tests good, go to Step 5. 5.Check the Hall Sensor by removing the control board P7 connector and testing for 5 VDC between P7-7 and P7-1. If test is good, go to Step 6. If test results are not correct, replace the Hall Sensor. 6.Replace all parts and panels before operating. 7.Plug in range or reconnect power. 8.Start a cook cycle and check for proper operation. 9. Enter the diagnostic mode to view the "Faults" screen. Press START TIME or DELAY START to clear each Fault code(s).

https://www.dnrme.qld.gov.au/__data/assets/pdf_file/0009/238617/natural-gas-conversion.pdf

I notice is it also in French, so I am guessing you are Canadian? Greetings from Mississauga! Its a guess... but..

YGY397LXUS Whirlpool Range Canada - Sale! Best Price ...

www.canadianappliance.ca > Ranges > Whirlpool

Whirlpool Gold YGY397LXUS Slide In Electric Range, 30in, 4.5 cu.ft, with AccuBake Temperature Management System, Self-Cleaning Oven, Delay Bake, ... This AccuBake system uses a sensor to monitor the oven temperature; it will then turn ...

Whirlpool GBD307PDS09 Built In Oven - Electric Timer - Stove ...

www.appliancetimers.ca > appliance

I have a Whirlpool Gold double oven and someone came to house and told me it ... black panel on whirlpool accubake system self cleaning oven gives double ... Somewhere hidden in the stove, should be the engineers spec sheet. It should be one of these images https://www.google.ca/search?q=%22whirlpool+gold%22+%22self+cleaning+oven%22+%22Accubake+system%22 Here is your error code There may be a problem with the Oven Temperature Sensor, the Warming Drawer Sensor (if so equipped), or the associated wiring. Power unit down by turning off the circuit breaker(s) for one (1) minute. ... Monitor the oven for one (1) minute to ensure the error code does not display again. Dec 14, 2019 F3 E2 - Electric Range - Product Help ' Whirlpool https://producthelp.whirlpool.com/Cooking/Wall_Ovens_and_Ranges/Electric_Ranges/Error_Codes/Error_Code%2C_Fault_Code_or_Message_-_Oven_Control/Starts_with_F3/F3_E2_-_Electric_Range#:~:text=There%20may%20be%20a%20problem,for%20one%20(1)%20minute.&text=Monitor%20the%20oven%20for%20one,code%20does%20not%20display%20again. ..

Depending upon the extent of damage, you may need both.

if it is a newer oven it has an ignitor and no pilot

yes, the keytail (connector ribbon) that plugs into the control board is not making good contact. simply cut a slip of heavy paper such as a business card to the width of the ribbon and slide it into the slot along with the ribbon connector. that will help press the contacts on the other side together snuggly and the problem will vanish. if the error ever returns, try pulling out the connector, cleaning the contacts with a pencil eraser, reinserting it into the slot and repeat above with the paper. good luck.