Whirlpool Kitchen Ranges - Recent Questions, Troubleshooting & Support

0helpful
2answers

We had a power outage and after the power cut back

if range uses electric.check fuses,and reset breaker.make sure proper voltage is going to the range.
10/28/2021 6:18:15 PM • Whirlpool... • Answered on Oct 28, 2021
0helpful
1answer
0helpful
1answer

Whirlpool Gas Oven Model WFG510S0AS2, Ser R44373042 Oven & Broiler NF

call your local gas appliance repair service .warranty was 1 year unless you bought and extended one
9/11/2021 9:06:52 PM • Whirlpool... • Answered on Sep 11, 2021
0helpful
1answer

Model GS475LEMS1. Why is it beeping constantly?

sad to say it but with a large family to feed perhaps a new stove is needed buying used is never the best choice
5/21/2021 2:03:01 PM • Whirlpool... • Answered on May 21, 2021
0helpful
1answer

Model GLP85800. How can I remove rear panel?

look for their secret hidden fastener
4/16/2021 5:11:33 PM • Whirlpool... • Answered on Apr 16, 2021
0helpful
1answer

F8E0 0n whirlpool gas range M: weg730hod50, What is going on, this is only 1 year old?.. reset and continues to error...

F8E0 Cooling Fan Speed Too Low Fan speed below 500 rpm, either because the fan is spinning too slowly or because there is a problem with the Hall Effect sensor. When will occur: Within 20 seconds of a fault condition when cavity temperature is above 170°F (77°C). RECOMMENDED CORRECTIVE ACTION PROCEDURE 1.Unplug range or disconnect power. 2.Pull the range forward and remove the top access cover. 3.Verify there are no obstructions in the blower. If there is an obstruction, remove it and go to Step 6. If no obstructions, go to Step 4. 4.Disconnect control board connect or P5 and check the fan motor for 105? resistance between P5-1 and P6-3. If the motor test is not good, replace motor and go to Step 6. If motor tests good, go to Step 5. 5.Check the Hall Sensor by removing the control board P7 connector and testing for 5 VDC between P7-7 and P7-1. If test is good, go to Step 6. If test results are not correct, replace the Hall Sensor. 6.Replace all parts and panels before operating. 7.Plug in range or reconnect power. 8.Start a cook cycle and check for proper operation. 9. Enter the diagnostic mode to view the "Faults" screen. Press START TIME or DELAY START to clear each Fault code(s).
2/21/2021 1:05:19 PM • Whirlpool... • Answered on Feb 21, 2021
0helpful
1answer

The model number and serial number on my Whirlpool gold electric stove have faded out on the sticker of my stove. Please help me in finding the model and serial number of the stove in the attached image.

I notice is it also in French, so I am guessing you are Canadian? Greetings from Mississauga! Its a guess... but..

YGY397LXUS Whirlpool Range Canada - Sale! Best Price ...

www.canadianappliance.ca > Ranges > Whirlpool
Whirlpool Gold YGY397LXUS Slide In Electric Range, 30in, 4.5 cu.ft, with AccuBake Temperature Management System, Self-Cleaning Oven, Delay Bake, ... This AccuBake system uses a sensor to monitor the oven temperature; it will then turn ...

Whirlpool GBD307PDS09 Built In Oven - Electric Timer - Stove ...

www.appliancetimers.ca > appliance
I have a Whirlpool Gold double oven and someone came to house and told me it ... black panel on whirlpool accubake system self cleaning oven gives double ... Somewhere hidden in the stove, should be the engineers spec sheet. It should be one of these images https://www.google.ca/search?q=%22whirlpool+gold%22+%22self+cleaning+oven%22+%22Accubake+system%22 Here is your error code There may be a problem with the Oven Temperature Sensor, the Warming Drawer Sensor (if so equipped), or the associated wiring. Power unit down by turning off the circuit breaker(s) for one (1) minute. ... Monitor the oven for one (1) minute to ensure the error code does not display again. Dec 14, 2019 F3 E2 - Electric Range - Product Help ' Whirlpool https://producthelp.whirlpool.com/Cooking/Wall_Ovens_and_Ranges/Electric_Ranges/Error_Codes/Error_Code%2C_Fault_Code_or_Message_-_Oven_Control/Starts_with_F3/F3_E2_-_Electric_Range#:~:text=There%20may%20be%20a%20problem,for%20one%20(1)%20minute.&text=Monitor%20the%20oven%20for%20one,code%20does%20not%20display%20again. ..
1/15/2021 11:07:04 PM • Whirlpool... • Answered on Jan 15, 2021
0helpful
1answer

Oven doesn't work on my whirlpool gas range. don't know why thinking it needs to have a pilot light.

if it is a newer oven it has an ignitor and no pilot
12/17/2020 3:33:22 PM • Whirlpool... • Answered on Dec 17, 2020
0helpful
2answers

I have a whirlpool range gs445lems and error code

yes, the keytail (connector ribbon) that plugs into the control board is not making good contact. simply cut a slip of heavy paper such as a business card to the width of the ribbon and slide it into the slot along with the ribbon connector. that will help press the contacts on the other side together snuggly and the problem will vanish. if the error ever returns, try pulling out the connector, cleaning the contacts with a pencil eraser, reinserting it into the slot and repeat above with the paper. good luck.
12/12/2020 12:03:50 PM • Whirlpool... • Answered on Dec 12, 2020
0helpful
1answer

Our whirlpool range oven door is noisy, it makes a terrible skriek when opening it, is there a fix and how ? thanks ,

try oiling it or spray wd 40 at the hinges
11/12/2020 9:59:35 AM • Whirlpool... • Answered on Nov 12, 2020
0helpful
1answer

I have Whirlpool accubake oven, older model, displayed on panel is F5E0 and door locked is checked, it keeps beeping until I push cancel. How do I fix these problems myself?

Try owner's manual, troubleshooting and the F5E0 error code. It may help, otherwise google the error code, or no owners manual? try https://www.manualslib.com
6/29/2020 8:57:43 PM • Whirlpool... • Answered on Jun 29, 2020
0helpful
1answer

Whirlpool stove what is sab

sabbath == When in Sabbath Mode, your oven will disable its automatic shut-off function to stay on longer than 12 hours. This means that the oven will stay in a Bake mode until shut off, which will allow you to use the oven for cooking or warming food.
4/12/2020 12:10:37 PM • Whirlpool... • Answered on Apr 12, 2020
0helpful
2answers

Whirlpool Electric Range W10400397B Error F2E0 on control panel

The F2 E0 error indicates a short at the key pad or a wiring issue between the control board and the keypad. Try pressing Cancel. Next turn off the range at the circuit breaker or unplug the range. Wait at least a minute before returning power to the system. Check if the error returns within a few minutes. Disconnect the power again and check the wiring between the control board and the key pad (if these aren't a single assembly). If the wiring connection is loose, secure the wires. If there is corrosion at the contacts, use a contact cleaner on the unit. Let the contact cleaner dry before connecting the power again. If the wires are damaged, replace the broken wires. If those steps don't resolve the issue, replace the key pad or keypad and control board depending on the unit. If the error returns after replacing only the keypad, then the control board has to be replaced. Please check the model number of the range. Current Whirlpool range models start with 3 or 4 letters, 2-3 numbers, another letter and another letter and 2 more letters. W10400397B could be a replacement part number for some specific item inside the range or the serial number. It isn't a valid Whirlpool part or model number at https://www.whirlpoolparts.com/ or https://www.partselect.com/Whirlpool-Oven-Parts.htm . I hope this helps. Cindy Wells
10/24/2019 1:42:22 AM • Whirlpool... • Answered on Oct 24, 2019
Not finding what you are looking for?
Whirlpool Logo

3,108 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Ismael Rodriguez...

Level 2 Expert

188 Answers

Cindy Wells

Level 3 Expert

6395 Answers

Are you a Whirlpool Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...