20 Most Recent
Frigidaire Affinity ATF7000E Front Load Washer - Page 6 Questions & Answers
Why is there a sheath in the drain pump?
Hey friend, that's a great question!
I am presuming you are speaking about the backflow preventer. This is designed to help when the water is pushed out of the pump. Therefore, it is typically normal that the sheath is in your drain pump. Hope this helps. -Matt
How to change atf6000fso door sensor
Good afternoon friend, thank you for your question!
I see you are trying to change the door sensor on your washer model ATF6000FS0. Please describe what your appliance is doing so that I can assist you better in pinpointing the problem before you take this step. I look forward to your response. -Matt
Washer doesnt pump much water in and doent rinse
Hi Friend, this is Z. Thank you for allowing me to assist you!
I see that your question is listed under Frigidaire washer, ATF7000E, and it is not filling with water or draining. Please confirm that the house valves are fully turned on. Otherwise, typically, faulty switch does not allow the valve inside to turn or a kinked fill hose. Other possibilities of more potential serious issues are water valve faults, faulty control board, pressure switch or wiring failure. If I was in your position, I will personally consult a professional to move forward accurately and assist with the repairs.
How to clean drain hose to frigidaire affinity front loader
One of the best ways to clean the drain hoze of a washing machine is to spool up the hose and place it into a bucket with at least 2 cups of vinegar (white or cider) and enough water to cover the disconnecfed hose. Soak overnight and rinse well before reinstalling.
Why does my Affinity washer flash on front and then won't run? Model FAFW3511KRo
Good Afternoon Friend, that's a great question!
Let's try resetting your washer by either unplugging it or flipping the household circuit breaker to the off position. It is important to wait roughly ten minutes and then turn on your washer. Confirm that the door is properly latched and try selecting a cycle. If resetting the power does not correct the issue, it could potentially mean a number of things: a potential wiring failure, damaged cord, faulty door latch assembly or control board. Because it could be a number of any one of several underlying causes, it would be advisable to contact an experienced appliance repair tech to assist further.
Best of luck! - Z
Why does the frfgidaire affinity washer has foul oder ?
Good Morning Friend,
I understand you have an odor in your Frigidaire Affinity washer, model# ATF7000E. Please try cleaning the inside of your washer by trying the following:
• Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock hazards.
• Dry around the washer door opening, flexible gasket, and door glass. These areas should always be clean to ensure a water tight seal.
• When extremely soiled items have been washed, a dirty residue may remain on the drum. Remove this by wiping the drum with a nonabrasive household cleanser. Rinse thoroughly with water.
• The plastic drum vanes may become stained from fabric dye. Clean these parts with a nonabrasive household cleanser. This prevents dye transfer to future loads.
To prevent the odor from coming back please try the following:
• Remove items from the washer as soon as the cycle ends. Excess wrinkling, color transfer, and odors may develop in items left in the washer.
• Periodically, wipe dry the bottom of the flexible gasket to remove lint and other debris.
• If there are no small children present, leave the door ajar to prevent odor build up and to improve venting of the unit.
I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.
-Best Regards-
WP
Frigidaire Affinity ATF7000E Front Load Washer locks the door then it doesn't start. What's wrong?
Good Afternoon Friend,
I understand the door locks on your Frigidaire Affinity washer, model# ATF7000E, and the load does not start. Please try resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Restore power and try any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.
-Best Regards-
WP
Frigidaire model gltf2940fs1 with no spin alert
From the way you have asked for a solution.
Most people like myself are not qualified repair techs.
Generally, by common sense or prior experience, we do the best we can. Since you have not added a possible error code. And even if there is one, most of them are confusing enough as to cause us to call a tech service.
That said. In order of possibility. Three most common problems for washer not spinning.
1) Bad Control board. Cost; $190 +/-.
2) Bad or broken drive belt. Cost; $40 +/-.
3) Bad motor. Cost $200+/-. Thes parts can be purchased off the I'net.
Alert!; Any of the three needs technical ability.
My advice is to call your friendly qualified service department.
Some say 2 days. Some say, if I can schedule you in to my work load. That locks you in to there system and you have to wait.
I have had good luck with Sears Repair Service. If you utilize them go on the I'net and download their discount coupons for any appliance service calls and repair parts if needed. And they are generally faster than the competition.
Good luck. (P.S., I do not work for or know any one who does
work for Sears. Just impressed with their service capabilities and speed of response. )
Affinity 6000 es1 error code ad
Good Afternoon Friend,
I understand that your Frigidaire washer, model# ATF6000ES1, is displaying an "AD" code. The "AD" means that your appliance was in an automatic mode. I suggest resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Restore power and start any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.
-Best Regards-
WP
How to clean the inside seal of a frididaire front load washer
Good Afternoon Friend,
I understand you want to know how to clean the inside seal of your Frigidaire washer, model# ATF7000E. Below are instructions for cleaning the inside of your washer, including the seal:
• Remove items from the washer as soon as the cycle ends. Excess wrinkling, color transfer, and odors may develop in items left in the washer.
• Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock hazards.
• Dry around the washer door opening, flexible gasket, and door glass. These areas should always be clean to ensure a water tight seal.
• When extremely soiled items have been washed, a dirty residue may remain on the drum. Remove this by wiping the drum with a nonabrasive household cleanser. Rinse thoroughly with water.
• Periodically, wipe dry the bottom of the flexible gasket to remove lint and other debris.
• The plastic drum vanes may become stained from fabric dye. Clean these parts with a nonabrasive household cleanser. This prevents dye transfer to future loads.
I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.
-Best Regards-
WP
Not finding what you are looking for?