20 Most Recent Frigidaire FWS833A Top Load Washer Questions & Answers

With the hose disconnected from the washer and faucet open no water comes out then it is for sure the washer will not fill, Run a garden hose from any working faucet and attempt to run washer> Do not forget and leave the faucet to the washer open if and when the blockage clears. The faucet that controls the hose connection may have failed and the internal rubber washer is blocking the flow. Hope this helps?

there is a water connector that the water lines from the house connect to the washer. you will need to take the panel off. you should see a blue plastic box where the hoses connect. you will need to replace this piece. it should have wires on it and that tells the washer when to open the valve for water to come through and when to stop.

either the thrust seal and washer are bad or its simply a build up of soap and hardwater deposits including fabric softner

i SUSPECT UR WATER PRESSURE LEVEL SWITCH

not takeing in water?

drum bearing worn or spider is cracked

FRIGIDAIRE TOP LOAD WASHERS WILL NOT SPIN OUT WHEN THE LID LOCK IS BROKEN

THATS THE TRUNION ON TOP OF CONE SHAPED PART IT HAS 2 BOLTS AND A PIECE OF METAL THEY SCREW INTO ON THE CONE SHAPED THING THOSE BOLTS BREAK ALOT IN OVERLOADING

Hi friend, thank you for your post!

From what you are describing it sounds like you could be experiencing a leveling issue within your Frigidaire washer. I would advise to check and make sure your appliance is leveled. Also if this is a new install please check to assure that the shipping materials have been removed.

If all of the previous information is corrected I would recommend having a professional come out to review your appliance because it could be an issue within the motor, belt, or drum. I hope this is helpful. -Matt

Good Afternoon Friend, I understand that your Frigidaire washer, model# FWS833A, will not stop filling. I see that you shut the machine off and the water runs onto the floor. I suggest shutting the water off at the inlet. From there I would contact your local authorized technician for further assistance. They will be able to diagnose your appliance and determine why the water will not stop filling your washer. Hope this is helpful. -Best Regards- WP

Hi Lynn, this is AP. I understand you are seeing stains and lint on your clothes once removed from your top load washer, model FWS833A. There could be several culprits causing this to happen. To confirm, are the stains not being removed during cycle or do you believe the washer is the cause of the stains? If you believe the stains are being caused from the washer it could possibly be undiluted liquid fabric softener poured directly on fabric. Something more serious could be a broken transmission causing oil to leak in the tub. There are some basic troubleshooting tips for lint to check such as undissolved detergent can leave residue on clothing. Separate clothing items which shed lint from items which attract lint. Permanent press, synthetic, knit and corduroy items will pick up lint from towels, rugs and chenille bedspreads. Make sure to Use correct amount of detergent, water temperature and water level. There are some simple troubleshooting tips listed above and in your owner's manual, if you find they do not resolve your concern I would recommend contacting a local authorized technician to inspect the washer. Thanks,

Hi Dante' Taylor, , this is AP! Thank you for your post I am not quite sure I understand your question regarding your Frigidaire top load washer. Would you mind providing some additional information on what part of your washer is currently locked please?

how to unlock nokia 520

Sounds like you may have a siphoning problem. The following link explains:

http://www.fixya.com/support/r587481-prevent_washer_siphoning

Double check your installation and drain hose placement. You need to ensure you have an air gap to break the suction caused by the drain line. In the event that this is not a simple siphoning issue, please let me know if you require additional assistance. I hope this helps you.

Hello rdying, thank you for allowing me to assist you! Based on what you mentioned briefly, it sounds like your washer possibly has a hole in the outer tub, loose or damaged drain hose/valve. Regrettably, this is not a simple DIY job. I would strongly recommend reaching out to a service provider to proceed further. Best regards - Chris