Top 20
Mitsubishi WD62527 62 in. LCD HDTV Questions & Answers
Wont come on
How many times this standby/power light blinks at one time switch ON? Count it carefully. These blinks are fault indication, and known as blinking codes. From the number of blinks occur at one time switch ON; you can get an idea about the faulty circuit stage inside the TV. This will make repair easy.
For more information, check the link http://electronicshelponline.blogspot.com/
11/20/2013 11:57:49 PM •
Mitsubishi...
•
92 views • 0 helpful votes
How to fix the ballast on my tv
Presuming the ballast is bad it is only available as a complete unit---Google the model number with "ballast" to locate a part number and or the part.
10/29/2012 7:22:26 PM •
Mitsubishi...
•
79 views • 0 helpful votes
My Mitsubishi wd-63527 turns on for a few seconds and shuts itself off.
The set may have (some models) a recessed reset button on front but that rarely does any good.This model should have two resets other than that one----soft reset if it has it is with Mitsubishi remote: On, Menu,1,2,3 enter.Set also has a hard reset which requires a four digit number code and resets set back to factory---it is a last resort and should not be done unless the soft one does not help.I would have the remote tested as without it you cannot do any reset--Most digital cameras in a dimly lighted or dark room will react on screen display when a remote is pointed at them and buttons pushed or most shops have a tester which will show and react to each and every button when remote is pointed at them and buttons pressed.This model could have a keyboard lock feature which disables the keyboard but remote should still function.First thing is to know if remote actually is working or not.
4/21/2012 4:28:36 AM •
Mitsubishi...
•
113 views • 0 helpful votes
Replaced lamp, tv worked great
Now the tv projection lamp tries to light up to the tv screen and shutting itself down,u hearing tv make alots of cliking noises to the tv set too?Yes,mean the Ballast board it is also dead,now must replaced the Ballast board too.The Ballast board only job are to ignite the tv projection lamp only.
8/9/2011 4:33:47 PM •
Mitsubishi...
•
235 views • 0 helpful votes
I have a mitsubishi 54in
Please tell me what exactly do you meanby opticel. Is it the optical block or is something else?
7/10/2011 11:17:13 PM •
Mitsubishi...
•
43 views • 0 helpful votes
I have a Mitsubishi WD-62530.
If you have sound and no picture on a DLP it usually means that there is a problem with the Lamp. When you say amber light, does this mean that its the amber lamp light?
12/16/2010 2:18:10 AM •
Mitsubishi...
•
654 views • 0 helpful votes
My TV turned off after a power surge, now a red
If the Lamp light is steady, the lamp has failed and must be replaced. The TV will not work until the lamp is replaced (and the lamp cover is properly attached). Call (800) 553-7278 to get a replacement lamp from the manufacturer. Order lamp part number 915P028010. Once you have the replacement lamp, make sure that the TV is off for at least 30 minutes before replacing. Avoid touching the lamp glass - it will shorten the lamp life. Unplug the TV and use a Phillips screw driver to remove the lamp cover from the back of the TV (2 screws hold it on the right hand side) . Loosen the two screws that hold the lamp cartridge (one on the bottom left corner and one of the top right corner). These screws will not come completely out. Grasp the handle and pull the lamp cartridge out straight towards you. Place the new lamp cartridge completely into the opening then tighten the two screws that hold the cartridge. Replace the cover and screw it back into place.
If the lamp cartridge or cover are not properly secured, the TV will not come on. (There is a safety interlock).
I hope this helps.
Cindy Wells
(the lamp should last at least a year; if not, contact the manufacturer for a warranty repair.)
10/10/2010 12:55:56 AM •
Mitsubishi...
•
389 views • 1 helpful votes
The green light flashes and
Replace Lamp PN# 915P028010 Encompass Parts Distribution has Free Service Manual for this Model and List of Parts PN# 1-800-638-3328
10/21/2010 10:28:17 PM •
Mitsubishi...
•
49 views • 0 helpful votes
Timer light just blinks and tv never comes on.
Hi
Thanks
for using FixYa. I am assuming it is Mitsubishi
WD62527 62 in. HDTV LCD Television as mentioned at the top of the issue. You'll
need to first check all components on the power board and DM board and then
would need to replace the faulty components. You'll need to use a multimeter to
check the circuits and components. This will take 4-6 hrs or less/more
depending on your expertise. If you do it your self you'll need an experience
to solder and desolder components on the board. Be careful as any wrong solder
can result in short and can cause severe damage to the TV. I'll suggest you to
do this only if you have repair experience of TV's. Getting this done from a
qualified tech will cost you around $200-220 including the components. And if
any board is to be replaced then it'll cost you around $300-350. Please
do accept the solution if the issue is resolved or post a comment for further
assistance.
Thanks
Rylee
5/8/2010 2:37:46 AM •
Mitsubishi...
•
147 views • 1 helpful votes
Not finding what you are looking for?