Canon FAXPHONE L80 Laser - Answered Questions & Fixed issues

What do you mean by "cannot receive"?

Can't you even start receiving manually? When someone rings, pick up the hanset and press START button - it should start receiving. Of course no document should be present in the input tray, otherwise it will start sending.

If you can receive manually, then all you have to do is to change the receiving mode between "Auto", "Fax/Tel" or "Fax", to get automatic pickup and receiving.

we dont rate consumer products --look up under consumer reports for review and guides of the different units

Hello.

NG means: Some or no pages sent.

Check the paper feeder to see if the page is pulling through.
Listen to see if the fax line "sounds"like it is working or if you hear dialing or not.

Hope this helps.

ECM is basically error correction mode. Tx is transmission. If you're having trouble transmitting, lower the default speed to 14.4kps. Fax transmit best on analog phone lines. Digital lines will work, but unless you have a digital fax modem 14.4 is often the best you can hope for. If you're on a voice over ip max speed is 9600bps and it probably still won't work. Buy an analog phone adapter for VoIP. If you're still having transmission troubles turn off ECM.

When you load your paper, you must press the Stop/Reset button for it to reconize you have loaded paper.

Look at where you install the toner cartridge. There should be a little tab or button or lever that the cartridge pushes once inserted. In fact, there is likely to be several, not counting the doors you opened to get where you are. Often, one of these tabs breaks, or lever bends, or button is misaligned. Just look around where you put the toner in, and ask yourself, "what is this supposed to do?" and as you go, also ask "what is expected that is not happening?"

Go buy a new one, it isn't fixable.

Press function then data registration and set/ok.It will say user settings,press the arrow down to get report settings,press set/ok,it will say tx report press set/ok and use the arrows to get output yes,press set/ok and stop!It will print one after every fax u send!Enjoy!

There is no way to reprint a fax once it's received. The report is all you can get.

RINGER VOLUME SWITCH
Use a pen or other pointed object to
select the ring volume of the handset (HI, LO, or OFF).

If you need the manual to see a picture of where the volume switch is located on the handset, send me an email to [email protected] I will send the manual to you right away. Please put CANON FAX L80 as the subject. Lawrence Brown

Welcome to Fixya

Turn off the machine for a minute or two. Unplug the cord from the wall socket then check the physical connection. Make sure the the phone line are intact on both ends. Turn on the machine then test the issue again.

Check the machine if it is in pulse or tone dialing. Please click here and go to page 9-3.

Thank you for using Fixya! If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

it makes it a lot easier if you change everything and know it's good for years.

here is the manual

http://www.usa.canon.com/app/pdf/copier/L80_SoftwareGuide.pdf

it is the paper jam sensor thats giving a false reading. It can b a very small piece of paper that u can easily remove with ur hand or by blowing. Open it, remove ink catridges, blow it thoroughly n make sure all sensors are clean of dirt. Also mke sure tht the paper u use is preheat to avoid these paper jams. Hpe it helps, pliz vote. Good luck.

Hello,
try to press red button stop and then green button start.
Or unplug it and connect again.

I assuming that actually dont had a paper jam prior to this message and dont have any paper disappear inside the Fax, then I could suspect the paper mis fed from the tray at the rear. That model can sometimes feed several sheets together or twist the paper as it is pulled into the printer.

Just below the sheet feeder is a jam sensor that is basically a plastic flag that when pushed by the paper breaks a light beam to indicate the paper is passing. If you get a paper jam in a printer it is important that the paper is removed in the direction it would normally feed through the printer.

If it is pulled against the normal flow of the paper then that plastic flag can break or be pulled off of it's hinges and cause a constant jam error. Either there is something still in the printer holding the jam sensor down or this has happened in your case.

There are 3 jam sensors across the path of the paper and 2 of which can suffer this problem. The one I mention and 1 in the fuser at the front. You would use a flashlight and make double sure that there are not obstructions that you can see either at the rear tray or the fuser.

If you can't find anything then the jam sensor are going to need to be checked but the rear jam sensor in particular is hidden beyond easy reach and involves quite a strip down to access so you may want to consider letting a technician do that for you.

If it had fed multiple pages in at once i would consider a new paper separation kit as they are easily fitted when the jam sensor is checked as they occupy the same area. Once multi feeding has started it often becomes frequent.

Hope helps.

try setting the answer mode to auto answer. It may be in manual answer mode. Also try calling your fax number and see if it rings.

Hi, please get new driver here: www.driversdown.com/
www.nodevice.com/driver/company/Canon/Printer.html
www.usa.canon.com/cusa/office/products/.../hs_1200ts

Jay vocdrs

Printing Problems
? The machine beeps while printing.
The machine may have a paper jam.
• Clear the paper jam (1 p. 13-3).
? Nothing prints.
The power cord may not be plugged in securely.
• Check that the power cord is plugged securely into the machine and into the wall outlet (1 p. 2-9). If the machine is plugged into a power strip, make sure the power strip is plugged in and turned on.
You may not have removed the plastic seal from the cartridge.
• Make sure you install the cartridge properly (1 p. 2-13).
The cartridge may need to be replaced.
• Replace the cartridge (1 p. 12-7).
? Printout does not match the print media size.
The print media may not be loaded correctly.
• Make sure the print media is loaded correctly in the multi-purpose tray (1 p. 5-4).
? Printout is skewed.
The print media may not be loaded correctly.
• Make sure the print media is loaded correctly in the multi-purpose tray (1 p. 5-4).
• Make sure the paper delivery slots are clear.
? Print media jams occur.
You may not be using the correct paper delivery slot.
• Select the correct paper delivery slot (1 p. 5-7).
? Printout is not clear.
You may not be using the correct print media type.
• Make sure you load print media that meets the requirements for the machine
(1 p. 5-2).
You may be printing on the wrong side of the paper.
• Some papers have a "right" side for printing. If the print quality is not as clear as you would like it to be, try turning the paper over and printing on the other side.
? Printout has vertical white streaks.
Toner may be low or unevenly distributed.
• Redistribute the toner inside the cartridge (1 p. 12-7). If the problem persists, replace the cartridge (1 p. 12-7).

Hey!There where u put in the document to fax,open the cover,look inside from the top to the bottom and see a big black roller,then a small one and then a long glass ccd!Make sure that there is nothing stuck on the glass and the white sheet opposite it!Good Luck!

Hi!Its easy!Simply press the function button and then DATA REGISTRATION button(Loacted on the left side of the machine!)It will say DATA REGISTRATION on the display!Press set/ok!It will say USER SETTINGS,press set/ok!It will say DATE AND TIME,use the arrows down un till u get un it name,press set/ok,press the C button and re-enter your name and when done press set/ok and stop!!Enjoy!!