Canon iP2700 Inkjet Photo Printer - Answered Questions & Fixed issues
How do i fix my printer?
Try to clean the encoder strip inside the printer,open the cover and clean it with your finger gently.hope it works
7/16/2015 3:01:35 PM •
Canon iP2700...
•
Answered
on Jul 16, 2015
•
114 views
I was riffil ink cartridge
After refilling your ink, it may prompt your ink very low... but it is nature there is no problem and effect for that... don worry! All the Canon printer prompt like that.... thanks
12/3/2013 4:00:02 AM •
Canon iP2700...
•
Answered
on Dec 03, 2013
•
1,089 views
Printer error 6000
follow this instruction and fix it. God bless you
-
1
Make sure that the printer is connected to a power outlet.
The power cable should be connected in the back of the printer and to a
working electrical socket.
-
2
Check that the wire from the printer is running to the
correct port on the computer tower. The wire runs from the small, square
port on the printer to one of the USB ports on your tower or laptop
computer.
-
Sponsored Links
-
3
Turn the printer on. Much of your printing failures can be
avoided by making sure that the power is turned on before selecting the
print command.
-
4
Install any updates or replacement software needed to run
your printer on your computer. You can get this software from the
manufacturer's website and will be notified through your printer drive
if there is something new to download.
Feeder Problems
-
5
Pull out all of the paper supply in the printer and make
sure that all pieces of paper are flat and whole. Any folded corners,
crumpled sheets or torn pieces should be thrown away.
-
6
Check the size of the paper you are using and check the
paper guide on the supply to make sure the paper is the correct size.
The paper guide is the small plastic clip that holds the paper steady in
the feeder.
-
7
Open the cover of the printer and make sure there is no
paper stuck within the feed rollers. You should pull out the jammed
paper if there is any, including any little torn pieces that may be
stuck inside.
-
8
Clean out the feed rollers with compressed air to remove any dirt inside the printer and refill the paper supply.
Ink Problems
-
9
Check the ink levels in your cartridges to see if you have
to replace the ink. You can do this through the control panel of your
printer software. If you don't know where to find these controls, just
search your computer for 'printer drive'.
-
10
Open the cover of the printer and wait for the ink
cartridges to stop in front of you within the printer. This will allow
you to take them out and replace them with full ones.
-
11
Pull the cartridges out of the printer. The number of
cartridges and how to remove them will vary with your model of printer,
but usually there is a small clip holding the top edge of the cartridge
in place. Just push this clip back and pull the ink out.
-
12
Pull the protective seal off the head of the new ink
cartridge. This is where the ink comes out and when you pull off the
seal it will allow the ink to descend.
-
13
Drop the ink cartridges into the printer and push each
cartridge into place. If there are clips you will hear them click when
the cartridges are in place.
-
14
Run a diagnostics test on your ink heads if your ink
problems persist after refilling the ink. This will help you clear out
the heads.
Read more:
http://www.ehow.com/how_6789824_troubleshoot-canon-printer-problems.html#ixzz2ZRL06I56
7/18/2013 10:45:14 PM •
Canon iP2700...
•
Answered
on Jul 18, 2013
•
101 views
Is this wifi enabled?
YES. THERE ARE SEVERAL USB-PARALELL CABLES CABLES IN THE MARKET. JUST CHECK IN THE WEB OR YOUR HARDWARE STORE. PRICE SHOULD BE AROUND 15 TO 20 US DOLLARS, DEPENDING ON BRAND, QUALITY, ETC.
SOME OF THE (MOST) BRIG A DRIVER CD.
ONE THING YOU SHOULD HAVE IN MIND IS THAT WHEN INSTALLING YOU BJC-80 IT WONT PRINT UNLESS YOU GO TO PRINTER PROPERTIES, PORTS AND UNMARK "BIDERECTIONAL COMPATIBILITY", THE GO TO ADVANCED OPTIONS AND CHECK ON "PRINT DIRECTLY TO THE PRINTER", OR SOMETHING LIKE THAT. (SORRY ALL MY SOFT IS IN SPANISH...) RESTART THA COMPUTER AND ENJOY. I HAVE A BJC-70 AND A BJC-80, USE THEM ON XP SP2 AND VISTA. BOTH WORKING FINE. DO NOT EXPECT SPEED PERFORMANCE. GOOD LUCK
8/6/2012 5:14:04 AM •
Canon iP2700...
•
Answered
on Aug 06, 2012
•
48 views
How to connect my printer to a router
This model Canon printer has onlt an USB connection to a computer.The only way to connect this printer to a router is to install a printer server with an USB connector, connect the printer to the print server and then connect the print server to the router using a LAN cable.The printer driver needs to be installed on all the computers on your network and then to the printer properties then Port tab and add a TCP/IP port then configure this port with the print server's IP address.Do a test print and if the test print is OK then printer is installed correctly.
5/29/2012 9:40:55 AM •
Canon iP2700...
•
Answered
on May 29, 2012
•
194 views
Colour cartige does not work poperly
If your cartridge is tricolor, surely one of the colors are finished, try placing the outlet on cartridge ink with a paper check you have the three color ink. Sometimes also be due to poor ink refill, I recommend using original cartridges, so you just make sure your cartridges are working properly ...good luck
4/23/2012 5:10:16 PM •
Canon iP2700...
•
Answered
on Apr 23, 2012
•
70 views
Reset ink level
Hello!To reset your printer please follow the instruction step by step.1. Turn off the printer without pulling the power cords.
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and release the Resume button.
4. Now Press Resume button 5 times then release both button.
5. You will notice that the Alternate Blinking error is gone, this means that
the printer is ready to use. good luck
9/28/2011 2:35:37 AM •
Canon iP2700...
•
Answered
on Sep 28, 2011
•
256 views
How do i only print black n white pics
Hello!1. Please press Ctrl + P after opening your picture.2. Go to Set up/Advance.3. Select your paper.4. Select Gray scale on the top of your paper size.5. Now press print. Your picture will be print with black & white... Good luck
9/27/2011 3:58:42 PM •
Canon iP2700...
•
Answered
on Sep 27, 2011
•
431 views
My ip2700 will not recognise
Hello! here is your solution..
1. Purchase Cartridge No. 810 & 811.
2. Press Stop/Reset button for 5 seconds without releasing the button.
3. After 5 seconds your printer will start its process... now release the button.
Good luck..
9/9/2011 12:57:05 PM •
Canon iP2700...
•
Answered
on Sep 09, 2011
•
178 views
When i print error 5800
This is an indication that the waste tank counter is full. This can be reset by using the following method.
First download this tool:
http://www.ziddu.com/download/11944259/PCM_servicetool.rar.html
Step 1: enter in service mode in order to used the resetter:
- Turn off the printer without pulling the power cords.
- Hold down Resume button and press Power button.
- Keep holding down Power button and let Resume button go.
- Then Press Resume button 5 times then let both buttons go.
- The Alternate Blinking error is gone: the printer is in Service Mode state.
Step 2:
- Extract the resetter and double click "servicetool.exe"
- Click Reload Button and you will get a new USB port.
- Load some papers in your printer and press the "Main" Button, wait until it shows "error 001" then press OK.
- Then press "EEPROM" button and the printer will print some text, after that click OK
- Then power off the printer (sometimes you have to press twice the power button to turn off) and turn on again.
- That's done.
I hope this helps, if so please rate this below.
Regards
GM
4/21/2011 7:42:16 AM •
Canon iP2700...
•
Answered
on Apr 21, 2011
•
400 views
Not finding what you are looking for?