20 Most Recent GE Profile JK915 Electric Single Oven - Page 7 Questions & Answers

Suitable instructions are here https://products.geappliances.com/appliance/gea-support-search-content?contentId=16246

F2 means your oven is sensing that it’s too hot. Try cutting electrical power to it for 5 minutes. If that doesn’t resolve it, either oven temperature sensor / probe or control board will need replacing

WB44T10010

I just need the dimensions of jkp62g0k3 to replace with new onw

Generally speaking, F2 fault code indicates the oven exceeded 590 degrees with the door unlocked. This could be caused by a stuck relay on the oven control board or it could be caused by high resistance in the oven temperature sensor probe.

If the element will shut off then the likely failure is the oven temperature sensor probe. The sensor is located inside the oven cavity. It will be protruding from the rear panel in the upper left or upper right corner. The sensor can be removed and replaced from inside the oven cavity

Cut breaker off for 5 minutes. That may unlock it after power is restored.

An F9 error code on a General Electric (GE) oven indicates that the oven's electronic control system has detected a problem with the automatic door lock. The automatic door lock mechanism prevents the oven door from being opened when the oven is set for "Clean" mode. The malfunction may be a jammed door lock mechanism, a pinched or broken wire, a faulty lock switch or a fault in the control board itself

Most likely display is bad and needs replacing

this error for GE means that your touch control panel has shorted and the entire touch control panel would need to be ordered and replaced if resetting the circuit breaker won't reset the issue.

actually it takes less time to heat up and cook with the fan running That is why it is called a fan forced oven as the fan forces the hot air all around the oven , heating it quicker and giving a better cooking result by moving hot air all around what is being cooked

F2 means it thinks the oven temperature is over 900 degrees with the door locked. You can try to cycle the power to the oven to clear the code. If that doesn't work then it could be the temperate sensor, or the relays bad or shorted out. Here is a amazon link for a relay that should look similar to what you have depending on your model #. Amazon com GE WB18T10352 Relay Home Improvement

Hello, You should replace the door lock mechanism and the door switch. Global Solutions Appliance Repair https://gsappliancerepairnyc.com/

First, I'm not a GE tech. * Check your warranty. Call for service. *** The following is for information only *** * GE Self Cleaning Oven instructions (a bit fuzzy); https://www.youtube.com/watch?v=2_hO7R29E9Y * Updated video (steam clean version); https://www.youtube.com/watch?v=yg3EBU99PSE * Older models (my mom's stove 1970's); https://www.youtube.com/watch?v=uBQa_yIyfgI * Be safe contact GE for specific questions.; http://www.geappliances.com/ Aloha, ukeboy57

Unfortunately, the F91 error indicates that the door lock is not functioning or the signal that the door is locked didn't get to the control unit. The range will not begin the self-clean cycle if there is a chance that you could open the oven door when the oven is dangerously hot. First try cycling the power by unplugging the range (or turning off the circuit breaker). Next check if the lock has engaged. If the lock doesn't engage, check if the mechanism is bent or binding. Next check the wiring to see there is damage that will prevent the communication between the control board or the door lock. Check for corrosion at the wiring harness connections. If the error happened after doing a self-clean, I'd suspect the door lock hadn't released. That can be related to a damaged over-temperature sensor or the lock itself. If the range has been self-cleaned before, it's possible that the lock was broken after forcing the door to open after that self-clean cycle. You may need to replace the lock, the wiring or the control board. Please add a comment with the model of your range for a parts diagram. If your range is under warranty, contact GE. I hope this helps. Cindy Wells