20 Most Recent
Toymax Magnavox 37MF337B 37 in. LCD TV - Page 2 Questions & Answers
I have had my tv
Hi.
Your tv has " capacitor flu".
Apparently, the companies in China, Taiwan, Indonesia, Bali, and a few others, made a whole bunch of capacitors that, knowing that they were junk, got put into tv's and monitors anyways.
The capacitors are supposed to have a life expectancy of around 25-30 years, but the junk ones are only lasting around 18 months or so.
It isn't anything that you did to the tv, it was doomed from the start.
About the only thing you can really do, is take it toa service point.
I suggest Fry's, or BestBuy, as they are the most trained for the repairs.
Before you get it fixed though, get an estimate of the repair costs.
I say this because the repairs may be as expensive as the cost of a new tv.
I hope this helps you out in understanding what happened, and good luck !
Sometimes when I turn on my Magnavox 37MF337B tv
you have some bad caps in the mainboard very common on this model the can shaped devices will have a puffed up top i would suggest you have a tech reaplce them they are hard to get out due to the large ground plain on the board you need a good hot iron
HDTV unable to get HD Channels w/ Antenna
The problem could be your antenna. Many people will buy small indoor tv antennas and wonder why they're not getting the signal that they want or the channels that they expect. Its not your fault. Digital signal is in two formats: UHF AND VHF. Some antennas only receive UHF. But many of the low band channels are VHF, so 1) you need an antenna that will receive those signals and 2) you need to know how and where to install that antenna and 3) you need to know if you need a signal amplifier depending on your coaxial cable length and number of connections.
I recommend visiting dennys antenna service (no I don't work there and I have never purchased anything from that website. He just has an excellent informational article with a great deal of "how to" on his pages.).
http://www.dennysantennaservice.com/2029710.html
This should be of great help to you.
Happy viewing =)
Magnavox TV model 37MF37B/37 - When initially
Hi rcbn
To answer your question;
There is a common problem with your magnavox set(also known as philips).
There are a few capacitors that go bad in the power supply and need to be replaced.
If your up to it here is the part location numbers and values;
C2074 2200mfds/35volts
C2080-2082 1200mfds/50volts
And any other capacitors that may look swollen or rounded tops in that area.
If you need help to locate them, let me know
Good luck
How to remove child lock from BELTEK TV?
general steps:
Get the TV remote control and push the "Menu" button and select "Options".
Select "Child Lock" from the "Options" list. On some televisions, the "Child Lock" is named "V-chip".
Choose the "Remove Child Lock" selection. Highlight this and then hit the "Enter" button.
Enter the four-digit code that you used when you activated the child lock feature. If you cannot remember it, your only option to deactivate the child lock is to reset the TV. The instructions for resetting a TV is written on the user's manual of the TV.
Exit the TV menu once you have entered the four-digit code. To do this, press the "Exit" or "Menu" button on the TV's remote control.
If you don't have a remote, you might try leaving the TV unplugged overnight. Some TVs will 'forget' their settings if left without power for a long period. You could also potentially buy a cheaper universal remote, and use that to turn off the child lock.
How to pairing Ruwido Amadeus R 9710 to tv?
To pair your Ruwido Amadeus R 9710 remote to your TV, you can follow these steps:
Insert Batteries: Your remote is powered by two 1.5 V AAA batteries1. Make sure to insert the batteries correctly.
Switch on your TV: Ensure your TV is turned on.
Press the TV key: Press the TV key on your remote control for approximately 4 seconds until the LED flashes twice.
Enter the Code: After seeing the 2 flashes and within 5 seconds, enter the 3-digit numerical code from the list provided with your remote2. After entering the code, the LED will flash twice indicating that the code has been accepted.
Test the Remote: Point the remote control towards your TV and press the key. If your TV does not respond by going into Stand-By mode then repeat steps 3 to 5 and enter the next code in the list.
Bed.-Anl. H2 Version1 (ruwido.com)
Not finding what you are looking for?