Washer shows F-23 (blinking) what could be the problem? I dont have my Manuel with me.

Mitsubishi TV Shutdown Troubleshooting - Stereo & Video ...

www.stereoandvideorepairco.com/.../MitsubishiShutdownTroubleshootin...
For example, the sequence: blink-blink, pause, blink-blink-blink, indicates an error codeof 23. This sequence repeats 5 times, so you can figure out if you are ...

Mitsubishi VS 50705 error code 23 - Service manual, repair and ...

forum.eserviceinfo.com/viewtopic.php?t=81051
Oct 24, 2010 - 10 posts - ‎4 authors Tv is old about 10 years. Shows error code 2-3 horizontal deflection failure. A few years back had a leaking crt, replaced the caps recomended ...

http://rent.rugdoctor.com/support contact them,they dont make instruction manuals

Thanks for your inquiry, Barbara Williams!

I understand that the lights on your Frigidaire washer are blinking and beeping. It sounds like your washer is providing a set of error codes. Your control panel may need to be replaced. I would recommend contacting a professional technician for proper diagnosis to be completed to avoid any unnecessary part purchases. Hope this is helpful. -Matt

F1 is a flood error. Below is a link to a video that you can download that shows you how to repair your dishwasher.

Solution

Good Luck

is it a slippery type of substance lift up and look on the walls around the inside of the washer if its all over the walls this is what we term the brown ring of death means in some models that the transmission is going or in your models case you dont have a transmission in your unit you have a drive motor that hooks directly into the bottom of the tub so first thing to do is remove the back rear and cover panel here is a link showing how to disconnect the panels http://www.searspartsdirect.com/partsdirect/partsdirect/showSubComp.pd?imageUrl=http%3a%2f%2fc.searspartsdirect.com%2flis_png%2fPLDM%2fW0802014-00001.png before you get to involved into this one of the first things you should check is the water pump and the hoses going to and from the pump itself if the pump is in good working condition the put a jumper wire on the lid switch wire and start the unit and see if you can visually see where the liquid is coming from here is another link check around parts 8,9 as well as 23 23 is the filter usually see a main seal between the two tubs but for some reason this site isnt showing a seal on this type of model so most likely you have water going somewhere that is corroding the metal hers the other link showing 8,9 and 23 http://www.searspartsdirect.com/partsdirect/part-model/Whirlpool-Parts/Washer-Parts/Model-WTW6600SW3/1198/0153200/W0802014/00003?blt=06&prst=&shdMod= please message me back with any further questions as well as your finds thanks again
Rick

Mine is doing the same exact thing. Just after I press "Start", the F1 starts beeping. Then at 23 minutes into the cycle, it does it again. So frustrating! What is wrong with this machine?

mine only turns green when its done charging. it blinks when i have a message or a missed call. i dont know if this will help though O.o

the lever that engages the belt on the deck check that most common problem is the deck set up parts dont move as easly if i can further help e-mail me wade at [email protected]

bestbuy.com is showing 8 for under $50:
Less than $50 (8)

If that link doesn't work, try pasting the following into your browser:
http://www.bestbuy.com/site/olspage.jsp?_dyncharset=ISO-8859-1&id=pcat17071&type=page&ks=960&st=Ethernet+Switch&sc=Global&cp=1&sp=&qp=crootcategoryid%23%23-1%23%23-1%7E%7Eq45746865726e657420537769746368%7E%7Ecabcat0500000%23%231%23%231u%7E%7Enf403%7C%7C4c657373207468616e20243530&list=y&usc=All+Categories&nrp=15&iht=n

is the lock symbol showing in the lcd badge when it's not back lit can be hard to see ,if it,s showing push lock button till it beeps release immediatly now try power button or start/pause button