Pvr not rebooting properly - Televison & Video

The "stby" message on your PVR 2 likely means that it is in standby mode. This can happen if you have turned it off, if there is an issue with the power supply, or if it is experiencing a technical issue.
The "footprint" message on your TV may indicate that the TV is not receiving a signal from the PVR 2. This can happen if the cables connecting the two devices are not properly plugged in, if the cables are damaged, or if there is an issue with the PVR 2 itself.
To resolve the issue, you can try the following:

1. Check the power supply to the PVR 2 and ensure that it is properly connected and turned on.
2. Check the cables connecting the PVR 2 to the TV and ensure that they are properly plugged in and undamaged.
3. Try resetting the PVR 2 by unplugging it from the power source for a few minutes and then plugging it back in.
4. If none of these steps work, contact your service provider or the manufacturer for further assistance.

http://tempoaustralia.com/sw/as-pvr1000r/AS-PVR1000R_IM.pdf

DG-DABVPR1TB
down load and put on a usb drive,
DGTEC firmware 2011 updates available

New updates available for service issues such as freezing and start up/ recording issues (firmware 2011) are also available from the DGTEC website.

Please update software first before replacing hardware...


From DGTEC Website Software Upgrades page: -


Click on the relevant link below to download the latest software update for your DGTEC product. For further help and assistance, please access the DGTEC Call Centre via the Support page.



Obsolete Products



* DG-FV500PVR Upgrade (zip file 4.3Mb)

* DG-HD6760 Upgrade (rar file 2.3Mb) Upgrade instructions DG-HD6760 (25Kb)



New Products



DG-HDMP1080

DG-HDMP1080P

DG-HDMP1080TT

DG-HDMP500TT

DG-DABVPR1TB

DG-DABPVR500GB

DG-HD2104AND



Models

DG-FV500PVR - 500GB HD PVR WITH TWIN TUNER (FREEVIEW)
DG-HD6760 - HD SET TOP BOX WITH USB RECORDING
DG-HDMP1080 - HD MEDIA PLAYER
DG-HDMP1080P - WIRELESS HD MULTI MEDIA PLAYER / STB
DG-HDMP1080TT - HD MEDIA PLAYER WITH TWIN TUNER
DG-HDMP500TT - (NEW MODEL RELEASE)
DG-DABVPR1TB - 1TB HD PVR WITH TWIN TUNER WITH INTEGRAT
DG-DABPVR500GB / DG-DAB+500PVR- 500GB HD PVR / TWIN TUNER WITH INTEGRATED
TV-6600 BAUHN UNIT- 500GB HD TWIN TUNER PVR
GG-HD1200PVR- BAUHN UNIT WITH TWIN TUNER
Note: - Master Override Password 1973



Instructions:



Read instructions carefully before commencing. Software needs to be carried out while the PVR is cold. Go to "Telefix" website and select "Service Guide" or "Download Service Manuals" and download software to a location on the PC Hard Drive.
Unzip file and copy "usb.upg" software onto a blank USB Memory Stick.
Plug USB Stick to USB port of PVR


Connect Power to PVR and switch on so that that the booting process commences.
Press 'Menu' button and scroll left or right by using the arrow buttons to find 'Installation' then press OK to select.
Note: PVR may freeze and not allow selection. Several attempts will be required to enable selection. If problem persists, switch OFF PVR to allow it to cool down then try again or use the alternative method.

Alternative Method



1a. Disconnect mains power.

2a. Plug USB Memory Stick to USB port.

3a. Press and hold the CH down arrow button on the unit and then connect mains power.

4a. When the display starts counting down release channel button and the upgrade interface will appear on screen.


7. Scroll down to 'USB Menu' by using the arrow down button then press 'OK' to select.

8. Scroll down to 'USB Upgrade' by using the arrow down button then press 'OK' to commence software update.

· Note: - Please do not shutdown PVR or remove USB Stick during the update process. When the update is complete the PVR will power down and reboot again as normal.

Once the update has completed, reset the PVR by restoring back to Factory Default.
Press Menu ? Installation ? Factory Default ? enter password 0 0 0 0 ? Select 'Yes' ? press OK to rescan channels.

Check Software Version, Press Menu ? Installation ? Version Info ? OK

download and put on usb drive

Software Updates

Pvr programs are played back from a hard disk drive inside or attached to the receiver. You may be able to reboot the receiver and pay back the event, there may be damage to the disk drive that caused it to freeze playback. You may also have had a signal issue during recording (especially with satellite based dvrs) that caused the image to freeze.

I'm unsure why you think it would have an IP address on the DVR. Does it actually have a network connection jack?
The manual doesn't reveal anything about networking:
http://www.nwtel.ca/media/documents/tv/dcx3510-m_user_guide.pdf

http://www.nwtel.ca/media/documents/tv/dcx3510-m_user_guide.pdf

check cable connections:
1. cable from wall to tv or to pvr. properly connected?
2. yellow,red and white in correct ports?
3. if HD, use green, blue and red to respective ports.
4. is remote properly sync to tv?
5. if no 3 above, get HDMI cable and connect to pvr.

If it shows on the desktop, go to utilities then disk utility and repair disk, also check as it may need formatting for the windows FAT format.

Your question is posted under the heading Sagem PVR 6280 so I'll assume that's the model which you have.

The Sagem PVR 6280 is specifically listed as a model which will have problems with the retune.

Seethe address below for a chart of affected models, but the officialadvice is that you must contact Sagem directly on 0845 0900 316 foreither an over the air update or an update DVD depending upon themanufacturer.

http://news.bbc.co.uk/1/shared/bsp/hi/pdfs/01_10_09_freeview2.pdf

SorryI can't provide you with a definite solution but I hope that I've atleast reassured you that it's not something which you have or haven'tdone!

Please return the favour by rating my answer.

Hi, I had the same problem, I downloaded the driver from this link:

http://www.kworldcomputer.com/download/download_pvr-tv305u.htm

This solved the audio problem

LG 32 LX2R TV REMOTE CODE TO WORK A SONY VTX-D8 U

The PVR h140 works on mpeg1 or mpeg4 format. If you need to convert avi files for example you will need a third party conversion programme such as Nero7 or similair free programmes. Check here for a 'how to' page. http://www.sharewareguide.net/article/Guide/guide:how-to-convert-video-to-mpeg4,-such-as-avi-to-mpeg4,-mpeg-to-mpeg4-and-vob-to-mpeg4-with-this-mpeg4-converter.html