Can i usedishwasher cleaner liquid - Washing Machines

This is a common issue, they make cleaning products to remove this gunk. Hot water and bleach will kill it as well.

Short answer is no, if the screen is plastic and the chemical attacks the plastic. If it is too much liquid and it seeps between any layers, it could evaporate over time, but you will likely have a noticeable dry stain forever.

For you and everyone reading this, never spray or apply any liquid to any TV, monitor, laptop, or cell phone screen directly, I think it says that in the owners manual. Always apply a light amount of TV screen cleaner spray to a microfiber cloth and then lightly clean the screen. DO NOT use anything with alcohol, ammonia, glass cleaner types, baby wipes, pre-moistened wipes of any type unless it specifically states it's for LCD monitors and TV's. If you or the manufacturer apply more cleaner to the wipe or cloth than necessary, blot excess cleaner with a dry paper towel so that the liquid doesn't run or drip when applied to the screen during cleaning.

Read these instructions carefully before
beginning the TUB CLEAN cycle.
1
Open the door and remove any clothing in
the wash drum.
2
Open the dispenser drawer.
3
Add liquid chlorine bleach or tub cleaner.
Some powder or tablet tub cleaners which
are manufactured for this purpose can be
used.
(NOTE : Do not add any laundry detergent
or fabric softener to the drawer when using
TUB CLEAN.)
- If using liquid chlorine bleach
Add liquid chlorine bleach to the bleach
compartment of the drawer.
(NOTE : Do not exceed the maximum
fill line and do not pour undiluted liquid
bleach directly into the wash drum.)
- If using powder cleaner
Remove the liquid detergent cup and
add powder cleaner to the main wash
compartment of the drawer.
- If using tablet cleaner
Add tablet cleaner to the wash drum
directly.
(NOTE : Do not add tablet cleaner to the
drawer.)
4
Close the drawer and washer door.
5
Select TUB CLEAN and press START.
NOTE : It is recommended that TUB CLEAN
should be repeated monthly.
If mildew or musty smell already exists, run TUB
CLEAN for 3 consecutive weeks.
After TUB CLEAN is complete or when the washer
is not used, leave the washer door open for better
ventilation and drying inside of the washer

Seems that you may have some kind of Dirt/Dust in your player. Buy a CD/DVD Cleaner with liquid to loosen any thing in the player If it has liquid with it, it's best to buy the cleaner with a cleaning liquid in it. When you use be careful t not put to much liquid on CD/DVD it may harm player and such

Hi,

If the liquid was plain water, then no problem. Just dry it out with a hair dryer.

However, if the liquid contained sugar, the solution is a bit more difficult. Sugar crystallizes as it dries and takes on the characteristics of concrete. Let's take the easy one first:

• Go to AutoZone and buy a spray can of CRC QD Electronic Cleaner.
• Plug in your vacuum cleaner and be ready to immediately turn it on.
• Spray the keybord with the cleaner.
• Turn on the vacuum cleaner and pass it over the keyboard until there is no trace of the cleaner.
• Repeat this process three (3) times.

If the problem still isn't solved we go the harder solution. Immediately beneath each key there is a latex or rubber prophylactic that protects the innards from liquids. It has to be cleaned off.and that means the key must be removed. Make small hook out of a paper clip. Insert it under the key and gently lift it up and off. Spray cleaner of the latx membrane and remove any remnants of the liquid with a clean cloth.

To reinstall the key just press it back on gently and it will click into place.

That should solve your problem. As a case in point, I'm typing this on a Microsoft keyboard that has been bathed in hot coffee on a couple of occasions.

All the best

Ben

Hi , Just simple ,
option 1:
Please open case and clean the lense
or
option 2:
use good lense cleaner cd with liquid.
just drop liquid on to cd cleaner ( excatly on brush)
then you run.
it will solve your problems.

Use a syringe filled with a liquid head cleaner. Add tip syringe with flexible hose (like the hose on the outlet head cleaning mechanic). Remove the ink tanks. Hose into the nozzle.Give the pressure slowly until the liquid head cleaner in the syringe out. Make sure no liquid is spilled in the vicinity of the nozzle. Replace the ink tanks, nozzle check and head cleaning. Is there a change from the nozzle check from the previous?

1 check the power source first.2. see if power is going to unit with meter.write me back if you need more infobut check that first.

yes if it sprays from the hose its the heater clogged its in the handle if no spray replace belt check on rinse only

It stays in place