3repairer/ adviser/consultant
Bill Boyd posted an answer for this Office Equipment & Supplies:
"photo paper is normally thicker that normal paper used in printers . try adjusting paper..."
Bill Boyd
Bill Boyd posted an answer for this Cars & Trucks:
"the check light is reporting a serious problem and the ecm goes into limp mode to protect..."
Bill BoydBill Boyd posted an answer for this Rover Cars & Trucks:
"replace the sensors or the TCM It is m not a mechanical problem but the sensors are not..."
Bill Boyd
Bill Boyd posted an answer for this Ovens:
"if you are using the correct globe ( not one from a hard ware shop but one from the dealer..."
Bill BoydBill Boyd posted an answer for this Cars & Trucks:
"It's the Nox sensors, take it to the dealer ASAP. My old truck had that problem due to. It..."
Bill Boyd
Bill Boyd posted an answer for this Garden:
"bad battery not enough to run the ignition and the starter but enough when the starter is..."
Bill BoydBill Boyd posted an answer for this Cars & Trucks:
"ecm fuse blown or fuse rated at 40 amps is blown"
Bill BoydBill Boyd posted an answer for this Ford Cars & Trucks:
"set at .010" inlet cold and .012" exhaust cold When the oil pressure comes up the..."
Bill BoydBill Boyd posted an answer for this Cars & Trucks:
"many pressure regulators have a pump control to switch off the pump when it reaches set..."
Bill BoydBill Boyd posted an answer for this Cars & Trucks:
"code p0731 refers to gear 1--incorrect ratio===causes ==wiring--TR sensor / switch---shift..."
Bill BoydBill Boyd posted an answer for this Cars & Trucks:
"adjust the mesh of the rack and pinion it indicates that there is too much play in the..."
Bill BoydBill Boyd posted an answer for this Cars & Trucks:
"broken tie rod end"
Bill BoydBill Boyd posted an answer for this Garden:
"the seals will have a part number engraved in the face of the seals take a seal to a..."
Bill Boyd
Bill Boyd posted an answer for this Motorcycles:
"broken ignition wire on the start circuit. ON any unit when you are in the run position..."
Bill Boyd
Bill Boyd posted an answer for this Electrical Supplies:
"check the operation of the oil level sensor . No oil no start"
Bill Boyd
Bill Boyd posted an answer for this Saws:
"many hardware shops or machine supply shops sell belts for band saws"
Bill BoydBill Boyd posted an answer for this Cars & Trucks:
"clutch plate/s are installed incorrectly"
Bill BoydBill Boyd posted an answer for this Cars & Trucks:
"my KIA Rio is the same until I open the door and then it all works"
Bill BoydBill Boyd posted an answer for this AC Cars & Trucks:
"you don't because if you have to ask , you have no idea of what to do. To start with if..."
Bill BoydBill Boyd posted an answer for this Cars & Trucks:
"the obvious place to work on would be the switch as bypassing it makes the winch work. The..."
Bill Boyd
Bill Boyd posted an answer for this Sander Tools & Hardware - Others:
"sorry , this site is not a retail shop go you the local agent for that unit"
Bill Boyd
Bill Boyd posted an answer for this Hardware & Accessories:
"try it and see normally such items loose settings once the power is removed"
Bill BoydBill Boyd posted an answer for this Cars & Trucks:
"if you have quick disconnect couplings , make sure that the connection is screwed all the..."
Bill BoydBill Boyd posted an answer for this Xerox Office Equipment & Supplies:
"do the normal connect process , the on the pc go to the xerox site and down load the..."
Bill Boyd
Bill Boyd posted an answer for this Sewing Machines:
"look in the head of the machine where the cam lever is attached to the shaft that holds..."
Bill BoydBill Boyd posted an answer for this HP Office Equipment & Supplies:
"connect printer to the computer go to add a printer select the hp printer model. go..."
Bill Boyd
Bill Boyd posted an answer for this Bonaire Air Tools & Compressors:
"press the reset /overload switch on the motor or replace the start capacitor"
Bill BoydBill Boyd posted an answer for this Sewing Machines:
"normal problem is that when putting the thread into the needle , the thread misses the..."
Bill BoydBill Boyd posted an answer for this Garden:
"you can get a complete set of carby adjusting tools from e-bay for about $ 30.00 delivered..."
Bill BoydBill Boyd posted an answer for this Sewing Machines:
"it is called bird nesting and the upper thread tension is not tight enough Proper needle..."
Bill BoydBill Boyd posted an answer for this Panasonic Office Equipment & Supplies:
"go on line a down load the driver from the Panasonic site and forget the windows drivers..."
Bill Boyd
Cars & Trucks 29108 answers
Computers & Internet 4716 answers
Garden 2071 answers
Cell Phones 1377 answers
Motorcycles 1016 answers
Washing Machines 1012 answers
Office Equipment &... 998 answers
Sewing Machines 970 answers
Televison & Video 889 answers
Health & Beauty 685 answers
