Question about Motorcycles

Open Question

I HAVE A 2004 BLASTER JUST BORED IT OUT 50 OVER NOW IT REVS REAL HIGH AND NOT GO DOWN PLEASE HELP

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 86 Answers

SOURCE: 2001 blaster losses power under a load.

check the compression and if thats good, remove the air filter and try to start. or possible air fuel jet needs adjusting.

Posted on May 06, 2009

ollie reece
  • 1167 Answers

SOURCE: carb tune up gilera runner 50

on the carb you will find 2 screw one will be quite far in than the over thats the one you adjust this is the mixture screw which controlles the air and petrol together unscrew it say 1/4 a turns at a time and see if it improves if it gets worse screw it the oposite way and see if that improves good luck buddy

Posted on Aug 10, 2009

ollie reece
  • 1167 Answers

SOURCE: trouble with 2004 blaster 200 idle

simple just turn the idle screw in 1/4 of a turn mate and its done 74197ac.jpg

Posted on Sep 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 Toyota Rav4 RPM Revs high but lose speed


You need the transmission tested for fault codes, it is computer shifted, if all checks ok with the control system then you have a failing transmission that will need to be rebuilt.

Dec 12, 2016 | Toyota Cars & Trucks

1 Answer

Od flashing; high rev at low speed; no dtc.


Bad Sleeves - Ford Servo Bore Transmission Fix Solution

www.fordservoboretransmissionfixsolution.com/blog/bad-sleeves
Original owner let it run low on fluid because of leak. ... The worn bores will cause slipping, hard shifts, and high revs between shifts from those gears. ..... Andy I bought a 02 mercury mountaineer v6 4.0 the the O/D flashes and service light is on ... Get on a flat surface at highway speeds and manually turn the OD of and on.

"O/D off" light blinking on dash? please help anyone? - Discussion ...

www.topix.com > Ford Explorer
Aug 24, 2009 - i have a problem with my 2002 ford explorer sport trac OD blinking... it will turn of if i .... That wire led down to the transmission speed sensor. ... the O/D off light started flashing and its revving really high before it will change ... 2004 Jeep liberty problems
Dec 9, 2011
Ford Explorer O/D Light, Slipping Transmission
Nov 20, 2011
2003 Ford Escape Rough Idle/Engine light blinking
Apr 20, 2011
FLASHING O/D OFF LIGHT 1995 EXPLORER V6 EDDIE BAUER
Dec 3, 2009
More results from www.topix.com

Dec 05, 2015 | Cars & Trucks

1 Answer

2004 Honda CR 125 R very high idle


Hi, Anonymous and the usual suspects are:
1. Throttle cables improperly adjusted, pinched or need lubrication.
2. Idle adjusting screw needs to be backed off.
4. Air fuel mixture adjusted too lean start with 2 full turns.
5. Intake system air leak.
6. Fast idle choke ramp is not releasing.
7. Broken throttle return spring.
8. Damaged diaphragm or slide.
9. Faulty MAP, TPS, ATS, O2, sensors or wiring/connector.
10. Multiple carburetors not in sync.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
CR125 overly high idle at low idle settings help
Cr 125 2002 idling high
Honda CR 125R 2002 Sevice Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda Elsinore CR125M Owner Manual

Apr 17, 2014 | 2004 Honda CR 125 R

1 Answer

Transmission is not shifting properly on my 2000 nissan frontier 2wd pick up, auto It revs at 3-4000 rpm instead of a nice consitent 2000rpm, revs real high and doesnt change gears intill 20 mph, it doesnt...


You could have a bad valvebody in your transmission or a bad pump in your transmission or your clutches are bad. In any case you have a bad transmission. Please rate my answer.

Nov 17, 2009 | 2000 Nissan Frontier

1 Answer

Trouble with 2004 blaster 200 idle


simple just turn the idle screw in 1/4 of a turn mate and its done 74197ac.jpg

Sep 10, 2009 | 2004 Yamaha YZ 250 F

1 Answer

2001 blaster losses power under a load.


check the compression and if thats good, remove the air filter and try to start. or possible air fuel jet needs adjusting.

May 06, 2009 | Yamaha YZ 250 Motorcycles

2 Answers

I have a 2004 yamaha blaster 200 i need a diagram or advice on the best way to take my carb. off, throttle cable from top of carb...


i can't seem to figure out why my 2004 blaster 200 won't idle properly. i cleaned the carb and replaced the spark plug. it revs fine but when it goes down to idle it just dies. any help?

Mar 01, 2009 | 2004 Yamaha YZ 125

2 Answers

Very low end power


Replace the reeds, Clean the carb jets and adjust mixture screws.


Please rate this a fixya

Feb 06, 2009 | 2003 Yamaha YZ 250

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...