SVA-USA Televison & Video - Page 6 - Recent Questions, Troubleshooting & Support
The power went out and having trouble getting tvto
This is the best solution for your problem as a 40 year experience with wires etc.
Go to the source of your cable signal connector .
Open it and clean the terminals with emery paper , sand the end of the cable shiny clean from corrosion , get a new barrel connectors with gold terminals if possible lengthen the ends of the cable , insert and tighten good, use thick rg-16 or rg 40 cable with good insulation ends crimped professionally with a crimpier or buy ready made , not from dollar store. Get a gold plated professional splitter if you need one or two , it will cost about 15 or more each . Make the cable runs as short as possible, using the thick good cables. If needed get a signal magnifier. From radio shack or the source etc. Connect them good and tight . Ground the splitters . Problem solved , you will get crystal clear channel 2 to 7 including 3 and 4 . Isolate the TV cable from other cables and power wires.
Vitally
When I plug it in the red remote stand-by light
flashing power light:
projection TV`s have many protective circuits in them, they protect
your CRT`s from damage, over voltage called x-ray, and many others, you
need to have it checked before the damage is more costly, your TV is
not happy and needs to be checked
1/31/2010 8:25:05 AM •
SVA-USA...
•
Answered
on Jan 31, 2010
I got a universal SVA
please verify the model number and brand name of the universal remote control u have.
1/20/2010 9:18:01 AM •
SVA-USA...
•
Answered
on Jan 20, 2010
Need to know how to
Do you not have owners Manual it will tell you how to program! You also need to post Brand Name of TV and Model number. Thank You.
1/20/2010 12:38:47 AM •
SVA-USA...
•
Answered
on Jan 20, 2010
SVA HD flat screen will not power on but power
Hi ladymacmel
To answer your question;
The problem you have is most likely caused by bad capacitors in the power supply circuit (very common nowadays).
You`ll need to replace those capacitors before you can get the set going again.
If you are handy with a soldering iron, then let me know and i`ll help you identify and replace them.
Also the model# of your tv would be handy for components identification.
Best regard
1/5/2010 2:21:13 AM •
SVA-USA...
•
Answered
on Jan 05, 2010
Telefunken lcd 19
open it and put a fan behind it if it operates ok then have a repair shop resolder the board if you have any components that show heat damage then have the shop install new ones, this will save you money.
NO SOUND ON TV
Try reset on audio setting to factory.Should get audio back.Not then ur backlight Video board have problems.
SVA television. Have model # EV1703 Remote no
When you say the remote doesn't get the channels I have to assume the channel entry behavior changed. I am not to familiar with this brand but these are the basics for most tv's. If you have not removed the cable input to the tv or unhooked anything before the problem started here are a few thing you could try. Push the menu or setup button on the remote and under the channel or setup option on the tv make sure it is set to Cable and not Air or Antenna. Run the tv through the auto channel search to reprogram the cable channels. This process can take close to 1 hour on some tv's since it has to scan through the digital and analogue tuners. This will allow your tv to add the correct cable channels and remove the unwanted ones. You should be able to enter the channel number or move up and down with the channel buttons on your remote.
SVA-VR20
Do you get sound? if you do, then the problem can be in the backlight inverter board or in the power supply section that supplys the power to the inverter board.
Not finding what you are looking for?