Fisher Ovens - Page 2 - Recent Questions, Troubleshooting & Support

Isolate power from device, remove screws to free back panel.

Loosen strainer for oven liner on left and right sides and remove clip to allow oven liner to slip forward.

Remove screw on front central upper clip.

From front, move oven liner forward a few millimetres to release gasket. Here you see the strainer at the rear has moved forwards a few millimeters.

Remove the old perished seal.

The new seal/gasket part number 573263 is installed. Reverse dismantling procedure to complete reassembly.

you need to either replace - or get the door hinges replaced, the spring in the hinges has weakened over time, if it is still in warranty, then they should replace them for free, if not, then take the model number to your local f&P dealer and buy new hinges. Remove the door and dismantle the door to gain access to the hinges, undo the 2 screws holding each hinge in place, clean the inside of the glas while apart, reassemble in reverse order.

center or higher

There are lots of different timers on fisher and paykal The last one I reset was a few weeks ago it involves pressing 2 buttons at the same time I think it was the oven on and oven off buttons but I am not sure You will know when you have pressed the right 2 buttons the display will stop flickering set the clock time using the up down arrow buttons The auto light should not be on if it is press the manual button Regards Geoff Stove Recyclers

if this is a gas unit then you should check the ignitor by doing an ampere test on the ignitor most ignitors draw 3-3.3 amps minimum when it drops below this amount it takes alot longer for the flame to light if the ignitor checks out good the next thing you would want to check is the oven tempreture sensor this also can be tested by doing an ohms test at room tempreture this should be reading between 1000-1100 ohms if you have any further questions message me back and please remember to rank how this opinion has helped when our chat has concluded thanks Rick

You should have 3 wires, the green is the earth. The other two would normally be blue and brown. If you have tried to change the element the missing one may have fallen back in or it could have been burnt off the element terminal and fallen down the back. Anyway you may have to remove the rear of the oven to locate it.

The error F4 means that Open oven temperature sensor (RTD)
You need to Check sensor harness and harness connection between oven
sensor and oven control.
Replace oven temperature sensor (RTD) if wiring is
ok.

only solution is to replace the socket. no other choice.

Hello there
Electronic ovens with a digital display use a sensor to monitor oven temperature. To solve temperature problems for these models, you may need to replace the sensor. On some digital-display models, you can calibrate the temperature using the key pad. See your operator's manual for details. Ovens without a digital display often use a mechanical system for controlling temperature. On many of these units, you can remove the thermostat knob and adjust the knob itself to more accurately represent the actual setting of the thermostat. If, when you remove the knob, there's a screw on the back of it with a small calibration plate, you can loosen the screw, adjust the plate, then tighten the screw again. If the knob isn't adjustable, and the oven temperature is off by more than 30 to 40 degrees, you need to replace the thermostat to solve the problem.

Hi


Thanks for using FixYa. From what you have described it seems to be the control panel that has gone bad. You can leave it unplugged for 5-10 minutes and then check if it flashes with an error code, if not then it seems to be the control panel that needs to be replaced as the power is getting to the unit however, it wont turn on. Please do accept the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

if its like a reg bulb it twists out

Hi Andy.



It depends on the oven model. If you can find the model number printed on service tag, you will be able to track the kitchen model.

If you have no model number you can browse a part site, then contact the online sellers to buy a knob that may be compatible.


Here different sellers:


Worldwide:
Appliance Parts -Research, Repair & Replace.

Appliance Parts from RepairClinic.com

USA:

Appliance Parts From PartSelect |

Appliance Parts Pros

UK:
eSpares

AU:

Welcome to Stokes Appliance Parts