Fisher Ovens - Recent Questions, Troubleshooting & Support

0helpful
1answer

Fisher & Paykel Thyme model. How do you remove these screw in type top elements please. Appreciate your help

To remove the screw-in type top elements of a Fisher & Paykel Thyme model, you will need to use a screwdriver. First, turn off the power to the appliance and unplug it from the wall. Then, use a screwdriver to unscrew the screws that are holding the elements in place. Once the screws are removed, the elements can be lifted out and replaced.
2/4/2023 5:47:03 AM • Fisher Ovens • Answered 3 days ago
0helpful
1answer

Oven keeps tripping Fisher paykell cooker range When I select function for oven it trips the main fuse box Setting temp sail first does not trip only when I select function ie fan assisted

Make sure there are no exposed wires, this will cause certain wires to touch and rip breakers, and also start a fire, if not dealt with.
12/7/2021 11:33:17 PM • Fisher Ovens • Answered on Dec 07, 2021
0helpful
1answer

How to take out fisher and paykel oven light bulb.

Turn off the power 1st then pop the cover off, carefully unscrew the old bulb with a pair of pointy nose pliers, screw in a new bulb pop the cover back on and turn on the power. Happy baking.
4/7/2019 7:33:00 AM • Fisher and... • Answered on Apr 07, 2019
0helpful
2answers

Oven door fails to close properly. Heat escapes

Probably mal-adjusted hinges. Open the door fully and there USUALLY are small holes in the hinges to insert a nail into to hold the hinges open while working on the door.
9/24/2018 9:07:40 PM • Fisher Ovens • Answered on Sep 24, 2018
0helpful
1answer

How do you start the clock on Fisher & Paykel

Fisher and Paykel does not know that model number. Could you recheck it please and advise us?
7/8/2018 4:29:32 PM • Fisher Ovens • Answered on Jul 08, 2018
0helpful
1answer

Have a Fisher & Pykle oven was cooking last night and then all power to it has gone, can you help?

It is a possible control board failure. Contact the website below for free diagnostic help and needed parts. Appliance Parts Accessories Repair Help
10/6/2017 7:44:24 PM • Fisher Ovens • Answered on Oct 06, 2017
0helpful
1answer

My Fisher Paykel built-in oven is about 8 years old. It takes over 30 minutes to heat to 350 degrees. Is this normal?

no indicates at least one element not working
7/18/2017 5:18:07 AM • Fisher Ovens • Answered on Jul 18, 2017
0helpful
1answer

How do I get the lubrication called white grease back in my oven racks on Fisher & Paykel oB30 model? There were left in the oven during self clean months ago. Thank you.

You can use a mixture of 1/2 cup white vinegar, 1/2 cup baking soda, 3 cups water. Mix all the ingredients together and coat the entire inside of your oven with it. After 5 min scrub the mixture off and wipe clean with a damp cloth. Don't forget to clean the heating element at the top. That helps with cleaning the racks or discoloration. You can try scrubbing the mixture with a toothbrush into discolored areas. White lithium has a drip temperature of 190 to 220 °C (370 to 430 °F). It is a lubricant used on hinges. It adheres strongly to metal, resists water, is non-corrosive, and resists heat. If from a spray can, the propellant smells strongly and is highly flameable and definitely is not something you want to breathe. Definitely air out the area. It can be acquired from Ace Hardware. Home Depot, or Amazon, among many other sources. It is sometimes referred to as Lithium soap.
6/12/2017 7:38:38 PM • Fisher Ovens • Answered on Jun 12, 2017
0helpful
1answer

Fisher double oven OD302. Periodically it will start beeping, shut off with no default code

Oven keeps beeping: As there is no reprogramming of most control boards try this, disconnect the power and wait 30 seconds and then reconnecting the power. If it's an "F1" fault code this generally implies an electronic oven control (EOC) failure. Disconnect the power, wait 30 seconds or longer and then reapply power. If "F1" returns upon power-up, replace the electronic oven control. The oven control can be accessed and replaced from the rear of the control panel. NOTE:Disconnect the power cord from the power source before removing the panel from behind the console. If its an F2 ERROR CODE, The F2 error indicates an open circuit in the oven temperature probe. Your range has a resettable thermostat in series with the oven temperature probe. If this thermostat opens the clock will display F2 and the oven won't heat. You can reset the thermostat by pushing in the reset button on top of the thermostat. Some ovens have an alarm that will beep continuously every six seconds to alert you that the oven is still on. Usually, a kitchen timer that you have set will cause the beeping, but occasionally it can be an error with the oven's settings. If it is the kitchen timer, you can simply push the "Kitchen Timer On/Off" button to end the continuous beeping. If that does not stop the beeping, it is probably beeping due to an error. You can turn the continuous beeping off but you may still need to troubleshoot the issue that is causing the beeping noise. Read more : http://www.ehow.com/how_12086370_ge-oven-stop-beeping.html How to Get GE Oven to Stop Beeping eHow
1/11/2017 7:38:45 AM • Fisher Ovens • Answered on Jan 11, 2017
0helpful
1answer

Why will my Fisher & paykel Aerotech OB76 oven not heat up when using the aero funtions

Some ovens require the door to be closed upon accepting the setting desired, AND then for the door to be closed. Reading your oven's manual may inform you of what to do. I am writing from experience, not making this up. A
12/3/2016 3:02:18 AM • Fisher Ovens • Answered on Dec 03, 2016
0helpful
1answer

Fisher & paykel b1602cte oven fan in element at back of oven not working

FIRST YOU NEED TO KNOW JUST HOW THE FAN WORKS, DOES IT WORK OFF OF ELECTRICITY OR IS THERE A COMPUTER CHIP IT WORKS OFF OF. DOSE IT WORK OFF OF JUST A SWITCH. LOOK UP ON LINE TO FIND A MANUAL FOR A FISSER & PAYKEL B1602CTE IT MAY TELL YOU WHY IT IS NOT WORKING.
2/3/2015 6:00:49 AM • Fisher Ovens • Answered on Feb 03, 2015
0helpful
1answer

Hi I am trying to

You can date most of your Fisher & Paykel home appliances very easily using the service at the following link: Appliance411 Service How old is my appliance Age finder date of...
11/1/2014 6:25:03 AM • Fisher Ovens • Answered on Nov 01, 2014
0helpful
1answer

Oven not heating up

It sounds like your oven heating element may have burned out. Check the element for a bulging area in the line. You may even see where it has ruptured or burned through. If so check the internet for a replacement element for your model. They are relatively easy to replace if you take your time. Most likely you will find a video on youtube showing you how to do the job. I hope this helps.
5/24/2014 1:53:01 PM • Fisher Ovens • Answered on May 24, 2014
0helpful
1answer

Oven fan does not turn off when oven turned off.

  • The fan runs on for a while after the oven is switched off to cool the oven compartment. It does go off eventually. This is the case for al fan ovens. I hope this helps
4/9/2014 12:47:23 PM • Fisher Ovens • Answered on Apr 09, 2014
0answers
Not finding what you are looking for?
Fisher Logo

54 questions posted

Ask a Question

Usually answered in minutes!

Top Fisher Ovens Experts

Marvin
Marvin

Level 3 Expert

85241 Answers

Tom Chichester

Level 3 Expert

62329 Answers

ADMIN Eric
ADMIN Eric

Level 3 Expert

37747 Answers

Are you a Fisher Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...