I need my tv zenith codes number

joe, the remote control codes are not the same from vendor to vendor. I think you're trying to program a universal remote control to operate your tv, if this is so, you will need to get the model number of the universal set and refer to the product code list, look under tv and zenith, another procedure you may try is the code search, this puts out all the available codes programmed into the universal set, just follow the instructions and be very patient because like I mentioned it will take you through all the available codes untill it will send the correct one for your zenith tv.

I have a Zenith Tv Model C27A24T and a Universal Phillips remote..i need codes

Hi cuddles3634!

For that remote, the tv codes are:

Zenith 1000, 1006, 1049, 1054, 1078, 1116, 1133, 1167, 1170, 1172, 1207, 1230

If the TV is digital: 1016
Hope that helps!

In my manual, to control a sony TV.. the code is number 8 or number 9.

You will hold down TV POWER, hit 8 then release TV POWER.
If that doesn't work, try number 9. Once the batteries are removed, it resets the code, so write it down. It will also over ride your old codes once you input the new one.

Note: Depending on your TV, some or all buttons may not function on the TV, even after entering the correct manufacturer code.


I looked for the section on Stereo, but all I found was the above.
Hope this helps.

One website (Thompsontv.com/zcodes.html), says that the setup code for a Zenith TV, using a Zenith universal remote, is one of the following numbers: 101, 142, 149, 177, 175.
If these numbers do not work, visit the Zenith website (Zenith.com) for contact info.
Hope this info helps you out. Please take a moment to rate this solution,using the rating system below. Thanks.

I own a One-for-All universal remote, and my booklet says the setup code for a Zenith TV ( without a built-in DVD or VCR) is one of the following numbers: 0017, 0092, 0178, 0463, 1265. I can not guarantee these numbers will work with your remote, but it is worth a try.

Zenith Product Codes

TV Mode Zenith Code 101 - VCR Mode Zenith Code 201 - Cable
Mode Zenith Code 353 - AUX Mode Zenith Code 401.

Programming Codes---
TV - 101 149 175

What´s the control manufacturer?

It's a Zenith remote, MBR 3440 is the model #, 124-202-01 is the part #. To program, press and hold PRG button until red light stays on, press TV,AUX etc, enter 3 digit code (www.xdiv.com) press Enter.

Here is the response from LG/Zenith customer support:

Unfortunately, this remote has very limited programmability. The manual is correct.

INSTRUCTIONS: Controlling other TVs with the remote You can control the sound level, input source, and power switch of non-LG TVs as well. If your TV is listed in the table below, set the appropriate manufacturer code.

1. While holding down TV POWER button, press the number buttons to select the manufacturer code for your TV (see the table).
2. Release TV POWER button. Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.

Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.

Manufacturer Code Number
LG/GoldStar 1 (Default), 2
Zenith 1, 3, 4
Samsung 6, 7
Sony 8, 9
Hitachi 4

For further information or troubleshooting, you may contact us at 800-243-0000 for LG Customer Service assistance. An agent will be glad to assist you. Please feel free to contact us with any additional questions or concerns. Thank you again for contacting LG Electronics.