Everstar mpk 10 cr 1 manual, have an error code of P-1

Here is the manual. The spill reservoir I imagine is inside unit. There is some information on page 8 Everstar MPK 10CR Use Care Manual Dehumidifier Operating

Prior FIXYA question:

http://www.fixya.com/support/t2766014-everstar_model_mpk_10cr_flashing_p2


Everstar Model MPK 10CR What does flashing P2 mean



Quoting:

Everstar Model MPK-10CR, What does flashing P2 mean?
I have a manual and it only talks about the error, P1, when the water container is for. Says nothing about P2. The unit will just completely shut off and then the red light is flashing and P2 appears in the window.
Posted by oyalajan on Aug 13, 2009

• Talk to a Repairman
• 1 Comment
• Flag
• More

• oyalajan Aug 13, 2009
  No, I do not add water to the unit.

×



2 Answers

zobs

• 
  
• Contributor
• 1 Answer

P2 means the bottom pan is full, you need to drain the bottom, small valve on the back bottom in the middle Posted on Jul 21, 2010

• Helpful 9
• Not Helpful
• 2 Comments
• Flag

• jerry1029 Jun 14, 2011
  My unit runs for about 5 or 10 minutes then shuts down blinks red with the P2 error message. I read what has been said but there is no water built up in my unit. i removed the plug , nothing. it does not run long enough to fill up. any ideas?
gerald young Jun 12, 2013
my unit is flashing p1 my unit is flashing p1 what is wrong

×

w_benjamin

• 
  
• Contributor
• 2 Answers

The filter that allows the water to get to the pump is clogged. Since the pump can't pump the water into the drain bucket, it fills the bottom pan up, the unit shuts down, and the P2 error code is then displayed. Posted on Jun 29, 2011

• Helpful 4
• Not Helpful
• 2 Comments
• Flag

oyalajan254 Jun 30, 2011
Where is the filter that is full that is not allowing the water to drain into the drain bucket, and is it something that can be cleaned? w_benjamin Jun 30, 2011
It should be near the pump that pumps the water up to the drain bucket. Each model is different, on my Everstar it was located under the housing for the drain bucket. The back and front of the unit needed to be removed, then the housing for the drain bucket needed to be removed. Not that hard, but a lot of screws. Take it out, then clean it with some dish washing detergent.

call in an electrician as there is a problem in the circuit allowing power from a neutral line and bypassing the switch

Everstar MPK 10CR Use Care Manual

Everstar MPK 10CR Use Care Manual Electrical Specifications

10,000 BtU's

I would google for a manual or an error code.

You can find the Use & Care Manual for your Everstar MPK-10CR here:http://www.supportuscenter.com/documents/MPK_Manual.pdf

The warranty & repair services for this unit are handled by Midea. I would suggest contacting their staff for the part.

Contact for Technical Service USA:
Contact Person: Winston Sankey
Tel: +1-305-591-8460
Fax: +1-305-591-8451
E-mail:[email protected]


I also did a search for you on AppliaceFactoryParts.com. This may be the part you are looking for:http://www.appliancefactoryparts.com/search/part/1371698/146072

Best of Luck!

Parts can be purchased on amazon, click here and take a look Amazon com everstar air conditioner. I hope this was helpful. Cheers

http://www.supportuscenter.com/pilot.asp?pg=Troubleshoot

Make sure the exhaust hose isn't longer than the maximum allowed and is not kinked, turned too many times (bends) and is the right diameter as specified in the manual. It sounds like the unit is going off on high head pressure.

If at all possible, change the exhaust hose to a smooth type rather than the corrogated hose that probably came with the unit. The less air restriction in the exhaust the better.

Seal any air leaks at the exhaust or discharge point.