I have a Emerson DVD/VCR combo player, have lost the directions, can't get it to work. EWD 2202

Hello
Setup codes for Emerson Tv with One For All URC-4021 remote control are:

0154, 0236, 0463, 0180, 0178,
0171, 0623

The One For All 4 Device Universal Remote Control is preprogrammed at

the factory to operate an RCA TV, a Toshiba DVD player, a Motorola cable

box, and an RCA VCR.To control devices other than the default brands,perform
the following steps; otherwise skip this section:

[1] Turn on a desired device (e.g.,VCR or DVD player) and, if
applicable, insert media (e.g., cassette or disc).

NOTE: Please read steps 2 through 4 completely before proceeding.

Highlight or write down the codes and device you wish to program
before starting step 2.

[2] On the remote control,press a device key once (i.e., VCR/PVR,
DVD, CBL/SAT,or TV).

NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo,

or TV/VCR/DVD Player Combo press VCR/PVR once.After programming

a VCR Combo device, you will be able to control channel selection,

volume, and VCR functions.

NOTE: To program control of a DVD Player,DVD Player/VCR

Combo, or TV/DVD Player Combo, press DVD once.After programming

a DVD Combo device, you will be able to control channel selection,

volume, and DVD functions.

NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR)

Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)
Combo, press CBL/SAT once.

[3] Press and hold SET until the LED (red light) blinks twice,
then release SET.

[4] Use the Manufacturer's Codes (starting on page 18) to

locate the type of device and brand name and then enter

the first four-digit code for your device. If performed correctly,
the LED will blink twice.

NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter
the same code again.

[5] Aim the remote control at the device and press POWER

once.The device should turn off. If it does not, repeat

steps 2 through 5, trying each code for your brand until

you find one that works. If it still doesn't work, try
Searching For Your Code on next
NOTE: If the device does not have a POWER key, press PLAY
OK.

TRY WWW. REMOTES.COM OR 1-800 REMOTES FOR EXACT REPLACEMENT

You can try this: Connect your DirecTv to VCR with Red/White/Yellow cables. Then the VCR to your TV with the same type of cables. Make sure the VCR is set to the video input, not the tuner. Turn your TV to the correct video input. Get the program ready on the DVR as if you were going to watch it. Press record on the VCR and then play on the DVR. At the end of the program, press stop on both. You may have a problem with the video recording properly. Some stations broadcast with copyright protection.

volumn control not working

Your DVD is preprogramed for Reg 1 only. It cannot be programed toplay Reg 8

called comcast

I went to the Little Leaps website and went into customer support and viewed a link that provided additional codes. I have the Emerson dvd player with video cassette recorder EWD2203 and the code 027 which was listed in the additional codes at Little Leaps website worked for me.
Here is that list of additional codes from the Little Leaps website:
018,030,035,005,150,151,043,058,011,147,148,016,004,002,144,007,009,146,013,020,027,133,042,129, and 149.
These codes were listed to try with any players.
Good Luck.

TV/VCR BUTTON WORKS FOR MINE

I sent you the manual if you dont get it. www.funai-corp.com/support you can download one there for free!

www.funai-corp.com/support for the manual. manual doesn't have codes, nor does the customer support line. you need to call direct tv and ask for FUNAI CODES. that is the manufactor of this unit.