I am guessing this is caused by some type of floating debris in your tank. I think that unit might just have a simple grommet holding the outlet fitting into the bottom of the tank. Try removing the outlet fitting and try to make sure the tank and fitting are free from debris.
Hi, The small permanent magnets that start the field producing the electric have gone flat or lost their charge. To get the generator part working again you will need to "flash" or reintroduce power back into the magnets.
This can be done in many ways... click here for one way
You can use numerous engine oils. 10W - 40, 30W Detergent, 30W Non detergent (SAE)
The best all around above 40 deg F and below 100 F oil to use is a 30W detergent oil. Brand name does NOT matter. Oil level should be checked EACH time you add fuel. Change oil any time the oil appears Dark BLACK when checked regardless of the hour intervals. .
You will either need to find a Coleman dealer in a store, in the phone book, or online.
Ask them for the part number of the switch, and then you can buy it in a store, or on the computer.
There is a store in Branson, Missouri, we were in last year.
On the computer, try Amazon or e-bay after you get a part number. God bless your efforts.
Check the circuit breaker(s) - also try connecting a smaller load to the generator to start out with, such as a table lamp. What are you trying to connect to the generator?
It may run in this condition for a bit, but it will eventually stop running and be in need of serious repairs. I would find a shop to replace the head gasket or a manual and gasket and fix it before running it again. If you need further help, I’m available over the phone at https://www.6ya.com/expert/thomas_e8f475a8655f7b4a
It may run for awhile in this condition, but eventually it will stop running and be completely ruined. I WOULD NOT RUN THIS WITH A BLOWN HEAD GASKET! My advice is to either find a replacement part, a manual and fix it, or find an authorized repair shop and have them fix it. If you need further help, I’m available over the phone at https://www.6ya.com/expert/thomas_e8f475a8655f7b4a
? 3:27
https://www.youtube.com/watch?v=IROa5QfPqkU
Nov 8, 2012 - Uploaded by Carlos Roman
This 5000 watt generator is great for backup power at home or forpower ... Coleman Powermate Generator 5000 Watts / 6250 Watts ... This feature is not available right now. ... folding handle, 1 quart, of oil, and 25ft generator convenience cord. ... How to convert a generator recoil starter to an electric starter!
pull cord won t retract Power Generators Questions ... - Fixya
www.fixya.com > Forum > Tags > pull cord won t retract
Power Generators pull cord won t retract questions and answers. Ask your pull cordwon t ... Question about Powermate Powermate 5000W Generator. 2 Answers · I was running my coleman powermate 6250 gen power ... cord 6250 trips out ... The pullcord does not rewind onto the pulley when pulled. At first I thought it was ...
After checking all connections check for power from the end of the alternator. if there is no power it is either the diodes in the end of the alternators rotor or the capacitor has blown ( round barrel shaped device with four prongs on ) When changing capacitor make sure you get the correct size mesured in micro farads.
this is a strange problem, the engine would not have left the factory in this condition. are the cam followers the same size ? have they been mixed up.
some engines have an auto decompression which consists of a spring loaded centrefugal weight on the camshaft gear and in order to close the valve the engine has to reach a certain cranking speed in order to compress
Hi Bob:
Sounds like the engine is seized.
Try removing enough bits so you can access the flywheel and see if you can turn it. Make sure ignition is OFF.
If the flywheel does not turn it will be time for a learning experience, a trip to the maintenance shop, or a replacement.