Top 20
Digidesign MBox 2 Mini (USB, includes ProTools LE software) 9900-55898-00 Volume License for PC, Mac Questions & Answers
Lost registration card from pro
Hello
You do not need the card, all you need is the receipt for the product or a copy of the charge if a credit card was used to make the purchase. Not having the registration card DOES NOT void the warranty. If you wish a replacement card you must contact the customer service department of the manufacturer of this tool.. Fixya.com is just a technical advice service and have no connection to Pro Tools.
M Box 2 Mini Can not be Found
have you tried Cs updates to your protools software? find the correct one for you by searching Cs updates at digidesign.com sometimes if you update you software, the firmware of your interface gets updated. Hope that helps.
Signal peaks automatically once track is armed for
Is there something plugged into your inputs, and are the pre amp channels turned all the way down? Also is your 48V phantom power turned off? To prevent damage to diaphragm or electronics of condenser microphones, the phantom power should be left turned off and only turned on after a mic is plugged in and the pre amp turned off and track unnarmed to prevent damage to speakers.
My mbox mini stopped working
Have you tried it plugged into another computer, just to see if it gets power? If it quit working and it hasn't been too long, you may be able to get it replaced for free where you bought it or from digidesign (digidesign.com)
What are the sign of
Hi
Few symptoms that your firewire is not working would be that the FireWire devices would intermittently drop off the bus. Another symptom was the Mac telling you that you had disconnected a FW drive (when you had not). Sometimes the problem manifested itself within the first two minutes of use; other times after 40 minutes. It first happened after the 10.2.6 update so you would be trying to get reinstalled the Combo updater (no improvement), and then after you did a clean install on another drive with 10.2.4 (same problems). Booting into single-user mode, you will see the following message appearing (all on one line):
IOFireWireSBP2Login::fetchAgentWriteComplete fetch
agent write failed! Retrying
It would repeat five or six times, then pause about a minute, and then repeat again, etc. Sometimes it would appear within the first minute after boot and other times it would take 30-40 minutes until it would appear - the same frequency the problems would develop when booted to the Finder. Suspecting a bad FW port (the lower port on the motherboard), I swapped the FW devices to the upper port...and the problem disappeared.
Let us know if you have something more to know else accept the suggestion.
Thank You for contacting Fixya.com
7/25/2010 4:46:26 AM •
Digidesign...
•
47 views • 0 helpful votes
Como cancelar el winter driver
EnglishIt is a car, and cars are complexbut no car was told , maker, model , and year.we can not guess cars. post the VIN? and all that is knownname a problem what can't your car do right?name symptoms or evidence that is confusing to you.then answers can happen.onlygood luck , finding itand Mucho Gusto.my guess now is this is posted to computer forumand not to CARS !must be some odd traction controls thing'but 10,000 models of cars,
How to resolve your meter when it's on temper mode
Tamper mode means the prepaid meter is in a mode where it does not supply power. Check your meter remote controller (used for recharging units). If it displays a Relay Open symbol, the meter is in tamper mode.
To remove tamper mode requires you contact the distributing company and request a tamper reset token. The tamper reset token is a 20-digit code that clears the meter from tamper mode and restores it to its default state.
My Employer Says They Are Going To Cut My Wages. Can They?
If you are in the middle of a contract, then cutting your wages is almost certainly a violation of your employment law rights. While I am by no means an expert on this matter, I did have a similar issue years ago - mid-contract wage cuts - and I hired an
employment attorney to fight the case on my behalf. It turned out that my employer was basically looking to scare people into taking the wage cut.
They got into some pretty serious legal trouble for their transgression, and nothing happened to me in terms of wage cuts after that. If you are between contracts, your employer can re-negotiate your salary, but as far as I am aware, if you are in an agreed-upon contract, they cannot just decide to reduce your salary. If you want to settle matters, contest this action with support from a legal professional.
Not finding what you are looking for?