20 Most Recent Ariston Technologies AWD120 13 lb. Washer / Dryer Combo - Page 5 Questions & Answers

I am supposing you are wanting a drive belt for your machine. Please type in "Ariston" on your search engine, as I did, and you will find that you can call them for your answers to your problems. After a little looking, I found them in about 4 minutes. God bless your efforts.

F18 - Communication error

You did not specify model! F08 - Heater relay cannot be activated

• Check wiring
• Check pressure switch and connections
• Tap relays as they can jam on new boards
• Check electronic control PCB
• Check heating element

Dado

F02 - Motor tripped, tachogenerator open circuit or short circuit. Dado

F08 - Heater relay cannot be activated

• Check wiring
• Check pressure switch and connections
• Tap relays as they can jam on new boards
• Check electronic control PCB
• Check heating element

Dado

F01 - Main modul, triac on board damaged or components feedback fault

• Short circuit motor triac on electronic module
• Check wiring
• Check electronic controller

Dado

Please follow this link: http://www.amazon.co.uk/Genuine-INDESIT-Washing-C00047317-C00196539/dp/B00XUC6Z5E Dado

F08 - Heater relay cannot be activated

• Check wiring
• Check pressure switch and connections
• Tap relays as they can jam on new boards
• Check electronic control PCB
• Check heating element

Dado

F10: Pressure Switch Empty and Full or neither Empty nor Full Pressure Switch Found Overhaul CN1 Overhaul Pressure Switch Wiring Control CN1/Pressure Switch Continuity Replace Pressure Switch Replace Card Dado

The washing machine fails to load water (The wording H20 is displayed). • The water inlet hose is not connected to the tap. • The hose is bent. • The water tap is not turned on. • There is a water shortage. • The water pressure is insufficient. • The START/RESET button has not been pressed. F01: Triac Short circuit Overhaul CNE Replace Card Dado

F04: Overflow and Pressure Switch Empty found at the same time (Pressure Switch stuck on Empty) Overhaul CN1 Overhaul Pressure Switch Contacts Control CN1/Pressure Switch Continuity Replace Pressure Switch Replace Card Dado

The washing machine fails to load water (The wording H20 is displayed). • The water inlet hose is not connected to the tap. • The hose is bent. • The water tap is not turned on. • There is a water shortage. • The water pressure is insufficient. • The START/RESET button has not been pressed. Dado

F05: Blocked Pump or Pressure Switch stuck on Empty Found Overhaul CNF (pump connector) Overhaul Pump Connector Control Pump Filter Control Pump Windings Change Pump Replace Card Dado

The washing machine fails to load water (The wording H20 is displayed).

• The water inlet hose is not connected to the tap.
• The hose is bent.
• The water tap is not turned on.
• There is a water shortage.
• The water pressure is insufficient.
• The START/RESET button has not been pressed.

Dado

F01 - Electronic circuit board fault Issue: Washing machine is not operating - some or all functions are not selectable. Cause: Main module, triac on board damaged or components feedback fault Advice: We recommend you disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply and wait 30 seconds and try starting the machine again. Dado

I had this issue also and it was because I started the machine and had not turned on the water to it. However, it cleared when I unplugged the power cord, waited about ten seconds, then plugged it back in. I guess they need a "reboot" once in awhile, like a computer - at least mine did. Hope this works for you, too.

This should do it. http://www.manualslib.com/products/Ariston-Avxl-105-3182207.html Ariston AVXL 105 Manuals