Keurig B50 Coffee Maker - Answered Questions & Fixed issues

go to wall-mart buy some coffee maker cleaner/ descaler and mix with water and run through the norm cycle! this should fix it.....i think the stuff is called clean rite

If your Mr Coffee emits a loud screeching sound during or after cleaning cycle and nothing stops it.....don't get a new one or take it apart and try to figure it out. Unplug for about 10 minutes and it resets itself.

According to their tech support...

Remove the water tank and re-seat. Unplug for 30 seconds and replug.

Fixed mine this way with the same issue.

Terry

Mine started off that way, then quit pumping any water through the K-cup. I overcame the problem with a reusable K-cup. If it will run a full cup through without the K-cup in place, this will probably work for you. They are available online and at some national chain stores for about $15.00. It's a little more inconvenient than K-cups, but better than throwing out a $150 coffee maker.

I have a Keurig today it sounded loud when priming and than wouldn't let me pick a size just large so I clean it with vinegar and water but it did same thing than I cleaned the screen on the bottom of resavoir I use a filter so I cleaned the screen on it that worked the same thing stopped it from working a couple of months ago the screen gets clogged scrub it with dish soap and soft tooth brush

Push the 2 buttons next to menu at same time then press menu. Wait for keurig lights to blink then release buttons. You just reset your keurig. Turn on and enjoy.

Hi,

There is air in the lines and it is blocking the water flow...
Here is a tip that will help you getyour Keurig to prime...

Keurig CoffeeBrewer will not prime
heatman101';
';

Keurig Good morning to you. Take a look in the manual and you have got your answer and coffee. all the best kolbrun

Prime means.... pumping. In other words the water in the machine goes through a water pump. That pump, pumps the water from the fresh water container in your machine and pumps it up through the machine, then goes into a heating element that heats the water and then of course flows over the coffee or tea that you put in your machine to give you a nice cup of hot tea or coffee. Priming is in a sense getting the air out or allowing the water to start flowing. If you have a vapor lock or air lock, you need to prime it to kind of help this pump start pulling the water up to the coffee. Hello, this is common. The pumps on these machines are not real good pressure. Sometimes you have to help it prime for the pump to work.So one very good way to solve the problem is to turn the machine on and lift the water reservoir up just a couple of inches and then jam it back in place fast and hard. With this way is like it injects just enough pressure into the system to open the check valve and when the motor pump will run you will realize that immediately water will passing through from reservoir to brewer tank. This procedure has to be done often between cups.From what we seen in internet their hundreds about the same problem but we have not see any serious response about it From Keurig's customer service yet.One other important and related problem frequently reported is the irregulars doses of coffee like HALF-FILLED CUPS of coffee e.t.aThis must be redesign from Keuring factory since there is not much we can do about it to solve once for all even if they will replace your machine with a new one you will have the same problem in few weeks. And definitely this not a problem due your Electricity in your area or due to hard water. However hard water areas will face bigger and more intensive the above problem so one more suggestion is to descaling the machine every week this will help a lot. If you find the above helpful please remember to vote for it Thanks Mike

Lift the reservoir, then reseat it. This will clear the prime message. If it repeatedly comes back then your machine is dead. If in the year warranty, call Keurig they will ship you a replacement. A very common problem.

Lift the reservoir, then reseat it. This will clear the prime message. If it repeatedly comes back then your machine is dead. If in the year warranty, call Keurig they will ship you a replacement. It is a common problem.

I'm not exactly sure, but most older models had either a foot switch or you pressed down on the body.

Call 1-866-901-2739

Not an issue after 2013, so get the new unit in 2014.

Needs resetting the Primer function

Get it from factory. Call 1-866-901-2739

Handle not fully engaged. Press down firmly to reset/

Call 1-866-901-2739 for factory assistance.

Unit was recalled due to fire and shock hazard.

Circuit board defective, happens a lot. Return for replacement.