20 Most Recent Apple iPod nano 2nd Generation MP3 Player - Page 2 Questions & Answers

Connect to the PC and scan for virus , if there are corrupt files it can hang up and so it is best to format and re-install safe files.If not the battery on the ipod can be faulty or there is fault on the main board.

push the play button and the center button at the same time until the apple shows up(takes like 20-30 sec.). I had the same problem before then hook it up to it. that should work :)

Welcome to Fixya

Looks like the software just hanged-up on you. Try to reset the Ipod by following the procedures below.

1st option:
Turn the Hold switch on, then back to off.
Press and hold the Menu and Select buttons for 10 seconds (until the Apple logo appears).
You may need to repeat the reset several times.
If the reset doesn't help, then put the iPod into forced disk mode.

2nd option (Disk Mode):
Plug the iPod into a high-powered USB port, let it sit for 2 hours, then disconnect it. If you have a wall charger, plug in the iPod, then follow these steps while it is still plugged in.
Turn the Hold switch on, then back to off.
Press and hold the Menu and Select buttons until the Apple logo appears
Immediately switch your figures to press and hold the Select and the Play/Pause buttons until "Disk Mode" appears at the top.
For a lot of people, this solves the problem. Connect the iPod to the computer and (assuming it shows up) reset the iPod again to get it out of Disk Mode. If at this point you still have the white screen, restore the iPod using the restore function in iTunes under the Summary tab (this will erase everything on the iPod and put it at factory settings).
Note: Do not disconnect or eject the iPod until the store is totally done. After you think it's done, wait another five minutes.

Thank you! If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

First and easiest solution is it may have been left on and the battery is dead, so plug it in and try that first. If that doesn't work, press both your menu button and the center (select button) for about five seconds, hold them down until you see the apple logo appear on the screen. That is your reset option. It will go through a shut down/reset process. When finished, turn it back on and enjoy....Brian

The device can be unlocked by connecting it to a computer while running iTunes

then you'll have to figure it out or try putting 0000

Have you tried turning the lock switch from locked to unlocked. There will be a little circular switch on the edge of the ipod that will appear red next to if it IS locked.

Hi, this seems to be a screen failure, just to make sure, do you still see the gray area when you reboot your iPod? in other words, can you see the gray apple over the black background when you first turn it on?
You can reboot your iPod by holding the menu and the select button (the one you use to pick a song).
If you can't see the Apple logo, then your screen appears to be broken, you're gonna have to take it to a technician. If by the other hand your iPod does show the logo, you really should try and restore it; this will erase all the songs and configurations but should restore your iPod to a working state, to do this just connect your iPod and while on iTunes, press the button that says "Restore".
--Dennis

According to Apple, if you have forgotten the code, you can unlock the IPod by doing the following:
Connect your IPod to the primary computer you use it with (the first one IPod synced with), and open iTunes.
When you disconnect iPod from the computer, it will no longer be locked.
If you can't unlock IPod using either [the code or connecting it to the computer you use to manage its songs]. . . you can restore your iPod to factory settings using iPod Updater. Please note that this will erase all data on your iPod.
Afterwards, you can add your music and data back to your iPod.
If you want to change the primary computer that your IPod is associated with, do this:
1. Restore your iPod. WARNING: The restore process cannot be undone.
All of your songs and files will be deleted. Always make a backup of your important data.
2. Connect your iPod to the computer that you want to be the primary computer.
3. Open iTunes and synchronize.
Apple also notes that company "representatives cannot unlock an iPod if you forget your combination. If you can't unlock your iPod and you don't have access to the primary computer, your only option is to restore the IPod, which will erase all music and data."
For this FREE answer, Please rate me

here ya go. that is not a problem follow the steps below. If you cannot remember the passcode, you will need to restore your device using the computer with
which you last synced it. This allows you to reset your passcode and resync the data from the
device (or restore from a backup). If you restore on a different computer that was never synced
with the device, you will be able to unlock the device for use and remove the passcode, but your
data will not be present Follow the steps that i have outlined below. If this does not completely help your situation
please let me know and i will be glad to assist you. According to Apple, if you have forgotten the code, you can unlock the IPod by doing the
following: 1 If you can't unlock IPod using either [the code or connecting it to the computer you use to
manage its songs. . . Plug the iPod USB cable into the bottom of the iPod Nano. 2 Plug the other end of the iPod USB cable into a free USB port on a Mac or PC computer. 3 Open the iTunes application by clicking on the Dock icon on a Mac or using the Start menu on a
PC. 4 Click on the name of your iPod Nano under the "Devices" list in the iTunes window. 5 Click on the "Sync" button to establish a connection between your iPod and the computer. 6 Click on the eject symbol next to your iPod's name after the syncing process has finished. 7 Unplug your iPod Nano. The device will be unlocked and you will be able to access all normal
features again. if that does not work you can restore your iPod to factory settings using iPod Updater. Please
note that this will erase all data on your iPod. Afterwards, you can add your music and data back to your iPod. If you want to change the primary computer that your IPod is associated with, do this: 1. Restore your iPod. WARNING: The restore process cannot be undone. All of your songs and files will be deleted. Always make a backup of your important data. 2. Connect your iPod to the computer that you want to be the primary computer. 3. Open iTunes and synchronize. Apple also notes that company "representatives cannot unlock an iPod if you forget your
combination. If you can't unlock your iPod and you don't have access to the primary computer,
your only option is to restore the IPod, which will erase all music and data." If you need further assistance please feel free to follow up with a comment and i will be here to
assist you. If this assisted you please feel free to rate the comment. thanks and have a great
day.Thanks, Midwest-tek

that is not a problem follow the steps below. If you cannot remember the passcode, you will need to restore your device using the computer with
which you last synced it. This allows you to reset your passcode and resync the data from the
device (or restore from a backup). If you restore on a different computer that was never synced
with the device, you will be able to unlock the device for use and remove the passcode, but your
data will not be present Follow the steps that i have outlined below. If this does not completely help your situation
please let me know and i will be glad to assist you. According to Apple, if you have forgotten the code, you can unlock the IPod by doing the
following: 1 If you can't unlock IPod using either [the code or connecting it to the computer you use to
manage its songs. . . Plug the iPod USB cable into the bottom of the iPod Nano. 2 Plug the other end of the iPod USB cable into a free USB port on a Mac or PC computer. 3 Open the iTunes application by clicking on the Dock icon on a Mac or using the Start menu on a
PC. 4 Click on the name of your iPod Nano under the "Devices" list in the iTunes window. 5 Click on the "Sync" button to establish a connection between your iPod and the computer. 6 Click on the eject symbol next to your iPod's name after the syncing process has finished. 7 Unplug your iPod Nano. The device will be unlocked and you will be able to access all normal
features again. if that does not work you can restore your iPod to factory settings using iPod Updater. Please
note that this will erase all data on your iPod. Afterwards, you can add your music and data back to your iPod. If you want to change the primary computer that your IPod is associated with, do this: 1. Restore your iPod. WARNING: The restore process cannot be undone. All of your songs and files will be deleted. Always make a backup of your important data. 2. Connect your iPod to the computer that you want to be the primary computer. 3. Open iTunes and synchronize. Apple also notes that company "representatives cannot unlock an iPod if you forget your
combination. If you can't unlock your iPod and you don't have access to the primary computer,
your only option is to restore the IPod, which will erase all music and data." If you need further assistance please feel free to follow up with a comment and i will be here to
assist you. If this assisted you please feel free to rate the comment. thanks and have a great
day.-Midwest-tek

According to Apple, if you have forgotten the code, you can unlock the IPod by doing the following:
Connect your IPod to the primary computer you use it with (the first one IPod synced with), and open iTunes.
When you disconnect iPod from the computer, it will no longer be locked.
If you can't unlock IPod using either [the code or connecting it to the computer you use to manage its songs]. . . you can restore your iPod to factory settings using iPod Updater. Please note that this will erase all data on your iPod.
Afterwards, you can add your music and data back to your iPod.
If you want to change the primary computer that your IPod is associated with, do this:
1. Restore your iPod. WARNING: The restore process cannot be undone.
All of your songs and files will be deleted. Always make a backup of your important data.
2. Connect your iPod to the computer that you want to be the primary computer.
3. Open iTunes and synchronize.
Apple also notes that company "representatives cannot unlock an iPod if you forget your combination. If you can't unlock your iPod and you don't have access to the primary computer, your only option is to restore the IPod, which will erase all music and data."
For this FREE answer, Please rate me

Hello , Welcome .
I'm glad to help you
You Can Download Free MP3 From Youtube By This Site : video2mp3.net
If you didn't found Your Favorite Music In Youtube Try These Sites : Beemp3.com or 4shared.com

i am glad to assist you with this. If you cannot remember the passcode, you will need to restore your device using the computer with
which you last synced it. This allows you to reset your passcode and resync the data from the
device (or restore from a backup). If you restore on a different computer that was never synced
with the device, you will be able to unlock the device for use and remove the passcode, but your
data will not be present Follow the steps that i have outlined below. If this does not completely help your situation
please let me know and i will be glad to assist you. According to Apple, if you have forgotten the code, you can unlock the IPod by doing the
following: 1 If you can't unlock IPod using either [the code or connecting it to the computer you use to
manage its songs. . . Plug the iPod USB cable into the bottom of the iPod Nano. 2 Plug the other end of the iPod USB cable into a free USB port on a Mac or PC computer. 3 Open the iTunes application by clicking on the Dock icon on a Mac or using the Start menu on a
PC. 4 Click on the name of your iPod Nano under the "Devices" list in the iTunes window. 5 Click on the "Sync" button to establish a connection between your iPod and the computer. 6 Click on the eject symbol next to your iPod's name after the syncing process has finished. 7 Unplug your iPod Nano. The device will be unlocked and you will be able to access all normal
features again. if that does not work you can restore your iPod to factory settings using iPod Updater. Please
note that this will erase all data on your iPod. Afterwards, you can add your music and data back to your iPod. If you want to change the primary computer that your IPod is associated with, do this: 1. Restore your iPod. WARNING: The restore process cannot be undone. All of your songs and files will be deleted. Always make a backup of your important data. 2. Connect your iPod to the computer that you want to be the primary computer. 3. Open iTunes and synchronize. Apple also notes that company "representatives cannot unlock an iPod if you forget your
combination. If you can't unlock your iPod and you don't have access to the primary computer,
your only option is to restore the IPod, which will erase all music and data." If you need further assistance please feel free to follow up with a comment and i will be here to
assist you. If this assisted you please feel free to rate the comment. thanks and have a great
day.

that is not a problem. If you cannot remember the passcode, you will need to restore your device using the computer with
which you last synced it. This allows you to reset your passcode and resync the data from the
device (or restore from a backup). If you restore on a different computer that was never synced
with the device, you will be able to unlock the device for use and remove the passcode, but your
data will not be present Follow the steps that i have outlined below. If this does not completely help your situation
please let me know and i will be glad to assist you. According to Apple, if you have forgotten the code, you can unlock the IPod by doing the
following: 1 If you can't unlock IPod using either [the code or connecting it to the computer you use to
manage its songs. . . Plug the iPod USB cable into the bottom of the iPod Nano. 2 Plug the other end of the iPod USB cable into a free USB port on a Mac or PC computer. 3 Open the iTunes application by clicking on the Dock icon on a Mac or using the Start menu on a
PC. 4 Click on the name of your iPod Nano under the "Devices" list in the iTunes window. 5 Click on the "Sync" button to establish a connection between your iPod and the computer. 6 Click on the eject symbol next to your iPod's name after the syncing process has finished. 7 Unplug your iPod Nano. The device will be unlocked and you will be able to access all normal
features again. if that does not work you can restore your iPod to factory settings using iPod Updater. Please
note that this will erase all data on your iPod. Afterwards, you can add your music and data back to your iPod. If you want to change the primary computer that your IPod is associated with, do this: 1. Restore your iPod. WARNING: The restore process cannot be undone. All of your songs and files will be deleted. Always make a backup of your important data. 2. Connect your iPod to the computer that you want to be the primary computer. 3. Open iTunes and synchronize. Apple also notes that company "representatives cannot unlock an iPod if you forget your
combination. If you can't unlock your iPod and you don't have access to the primary computer,
your only option is to restore the IPod, which will erase all music and data." If you need further assistance please feel free to follow up with a comment and i will be here to
assist you. If this assisted you please feel free to rate the comment. thanks and have a great
day.

it will still work but u just dont have a screen that works mine is the same way if you want a screen u might have to get a new one but if you just want to listen to music turn it on and hit the play butten

Hello,

There are two options by which you can unlock the code on your ipod. Follow any of the procedures below to unlock your ipod.

Unlock with the Primary Computer

1. Plug the iPod into the primary computer linked to that iPod, the first computer you synchronized it with unless you have designated another computer as the primary computer.
2. Open itunes and sync the iPod as normal.
3. Remove the iPod, following the normal removal procedure. The iPod unlocks automatically as you remove it.

Unlock by Restoring

1. Restore the iPod to factory settings if you do not have access to your primary computer. This erases all of the data you have stored on the iPod.
2. Plug your iPod into the new computer you want to be the primary computer. Open iTunes and click on the "Restore" button.
3. Reload your data, if it is available and sync your iPod. Remove it following normal procedures.

Take care

yes format your IPOD but make sure you do back up files for your important files, then install itunes on your pc and update firmware...

All right, the following section will show you the best way to help you with the conversion.
Download:
1. Download, install and launch Video Download Studio from http://www.downloadvideos-convert.com/download-videos-music.
2. Click” add URL” button to paste the URL of the video you want to
download. ( or you can play the video on dailymotion and click “auto capture”, Video Download Studio will automatically capture and download the video for you.)
3. Download details will showed on the working window.
Convert:
1. Click” convert” button on the top, you will switch to convert interface.
2. Click ”add” button to load your videos to Video Download Studio
3. Click” profile” drop-down list to select MP3 format.
4. Click” convert” button on the bottom, you will get MP3 format video in seconds.
As you can see, these simplest steps enable you to convert video. Join in and do it yourself, you will get a lot of fun.get it from http://www.downloadvideos-convert.com/download-videos-music

Your phone software has a glitch and it may need to be restored to factory settings.

ok this is a first step before trying to restore.

Take out your battery.
wait like 15 seconds and put back in.

see if this resets back to normal.

if it prompts you to do a factory restore at this point .. follow the instructions prompted.

The phone need the reset.

write back if this works or not.

I will try more with you. be patient o.k.

Hope this helps!