20 Most Recent
HP DeskJet 3940 InkJet Photo Printer - Page 9 Questions & Answers
Lost my installation CD and downloaded the software from HP but doesn't work
To register .dll files follow these steps:
1.
Click Start, click Run,
type cmd in the Open box, and then
OK.
2.
At the command prompt, type the following commands, and
press ENTER after each command:
regsvr32 /u sccbase.dll
regsvr32 /u slbcsp.dll
exitNote Click OK if you are prompted.
3.
Restart your computer.
4.
Click Start, click Run,
type cmd in the Open box, and then
click OK.
5.
At the command prompt, type the following commands, and
press ENTER after each command:
regsvr32 sccbase.dll
regsvr32 slbcsp.dll
exitNote Click OK if you are prompted.
6.
Restart the computer.
Out of paper
refill it but not necessarily with as much
paper as it can possibly hold - many printers like a little elbow room
in their paper trays. Make sure to feather the pages to eliminate
static. Hold the pages in one had and flip through the pages at a fast
rate with your thumb. If the paper tray is not empty, check for a
misfeed. A sheet may have been caught in the mechanism. There may be a
variety of printer access doors to check. Pull out any remnants. Even
the smallest piece of paper could be causing the problem, so check
carefully. Tweezers are handy for this procedure.
Printer not taking power.
since a local service has told u n u still want yr printer working i'll advice u to take it to some other service centre to look into it.
but the usual problem with yr model of printer not powering on normally is a s a result of the logic board being bad. once the logic board is being replaced yr printer should come up..
but be very sure yr problem is not from the adaptor that is i hope u have checked it and is working very well.
thank u
Printing from e mail
if your printing just click the print preview in the website and try to see if this would fit the landscape or portrait size of the content of the reservation. try to set that to by clicking file (from the website on the top right of your screen facing to you, then click page set up and have set according to the preview that you had .
ally
Light blinking
Sounds like you have a paper jam somewhere. Open up the printer and look for some paper. If the page is still in the machine, sometimes you can gently pull ever so slowly and finish getting the paper out of the machine. Power cycle the machine and if it was a jam, you should be fine.
About software cd......
Hi,
Software on CD, No longer available For Windows 98.
Go here to download drivers For Your Printer.
:-http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?product=445449&lc=en&cc=uk&dlc=en&submit.y=6&submit.x=3&lang=en&cc=uk
Mike @ Compurepair.
Printer does not work
Is it a HP model? had a similar problem, i downloaded the software from the HP website and it worked fine!
Printer won't print
switch of the printer first remove the usb cable from the printer and uninstall the printer driver nad remove printer from device manager also. to go to the device manager do these steps first right click on my computer and then go to properties and the click on hardware tab and then click on device manager and go to universal serial bus controllers just click on + tab it will expand and it will show the list of connected hardware select usb printing support and right click on and uninstall then restart you system. after coplete boot run the driver software and connect the usb cable when it will prompt you and switch on the printer. it will install your printer
Not Printing
Hi,
is there a possibility that the office 2007 downlooad was corrupt ?
This version of office, is noticably sower than previous versions, of Office.
I personally prefered Office 97, 2000 was the same, glitchy and very sluggish. it,s ok upgrading to these latest versions, providing you have the Computer specs, to match the software requirements. Hers a couple of Options.
1:- un-install the Office 2007 program, hopefully you have a version on cd of your older version ?
2:- if your running win XP, restore your computer to an earlier restore-point, before the upgrade.
This will reset your computer to how it was before the download.
3:- un-install then re-install your printer and related software/Drivers.
Mike @ compurepair.
NOT WORKING
try unplugging ALL power and USB cables. ESPECIALLY IMPORTANT... Unplug the USB cable from the back of the computer.
Then power down your computer and start it up again.
This worked for me last year when I had the problem you are having.
Urgently help me printer not recognized.. hyd
hi!good pm...hope this will help...
try to check the USB cable connected to your cpu & printer,see if its inserted properly...or try to plug the USB cable to other USB socket...if this does solve your problem,get another USB cable & try it...
goodluck!
Will not print from internet
Download, install and print from Mozilla Firefox.
Also download the Lexmark Toolbar, it works for any printer and is perfect for web printing.
Printing only blank pages
you have to go to the printer settings start printer properies ink or color than change to color because you can set your printer to print color or just black does not matter if that one has color if the setting is for black it will print just black
Not finding what you are looking for?