20 Most Recent Soyo KT600 Dragon Plus Motherboard - Page 2 Questions & Answers

Mic & LED connector J30;
Pin1 Line_Out_L
Pin2 GND
Pin3 Lin_Out_R
Pin4 GND
Pin5 MIC IN2
Pin6 GND
Pin7 LAN_Active_LED
Pin8 VCC

Just enable the SATA and your system should look up any installed SATA disks and boot from there. Just give it a try first.

Hi,

When system is switched on press on F2 if it does not take then again switch on and press Del or then try one option F12.

Regards.

Try all of the "F" keys, one at a time, and also try the "del" key. It has to be one of those. Power up the computer and continuously press, over and over, the chosen key. You should be able to hit on it.

Tiger Direct has a memory configurator that will have the information you need.

make sure that your bios is up to date by visiting your manufacturer's website and comparing the most recent release to the numbers flashed on your screen on post. If not, flash your bios using the instructions on the manufacturer website. Did this solve the problem?

Here is some great PC solution by Some FIXYA EXPERT. Get any kinds of PC solution from bellow.

1. Intel MotherBoard
2. Mercury Motherboard
   
3. Gigabyte Motherboard
4. MSI Motherboard
5. P5GC-MX/1333 Motherboard
6. ASUS Motherboard
7. IBM
8. Packard Bell
9. via

fahima29

try changing the drive configuration in the bios to recognise it as IDE

u can try here
also use drop down section for refine your search

This burner has some type of virtual software built into the drive called "Bluebirds". Bluebirds is advertisement linked to the LG website to get you to buy more LG products. If you choose not to install the software you will be prompted to install it every time you close the drive door. If you install it you get the tray icons pointing to more LG products. If you remove it from the startup it adds itself back to the startup every time you close the drive door.

http://en.wikipedia.org/wiki/Advanced_Host_Controller_Interface

http://driverscollection.com/?H=SY-KT600%20DRAGON%20Plus%20v.2.0&By=SOYO i didnt have time to test the links but it has info on the divers making it easier to find each one elswhere via file searching

Had problem like that.Removed board and isolated from touching anything metal.Plugged in memory and video card.Shorted power jumper and booted into bios setup.One of motherboard standoffs was in wrong position and shorting out mb.

Generally speaking
1 2 3 4 5
o o o o o
o o o o x
6 7 8 9

1-2 power LED 1+ 2-
3-4 power switch
6-7 HD LED 6+
8-9 Reset

I was able to go to a memory retailer who had an oline feature that matches memory to *********** board. I used a google search "Memory Capabilities for KT600-8237 motherboard and it was listed on the first page. I found out that the board can support three sticks at 1GB each for a total of 3GBs of memory. Problem solved.

is in bios, on advance setings or something the same, or in integrated periperals, after u find him push enter or arrows keys to set on disable, this in most of the case fix the prob, and is a via cipset then i tink is a ac'97 integrated audio in moust of the case (sorry for my english) 

http://www.soyo.com/uploads/downloads/manuals/k7/mk7vkp2%2011.pdf

here is the pdf with your user manual from the board.
the pci indeed is the slot for the modem and for the sound card,also.
the pci are slots near the agp slot..shorter than the agp.they are equivalent so you can put the modem and the sound card and to interchange the place if you want.
I think youll find more usefull infos in the manual anyway.
good luck


bye

make u r hard disk slave. by jumper setting ..provided atback side of ur hd pins.. and there also shouild be instruction os ur hd ..that ? u can make it slave.. read instruction on ur hard disk carefully. i m sure it will solve ur prob mann. best regards & best of luck.. mail add- [email protected]

-Check your cables and power status first. -verify your internet connection via router or modem -Scan for viruses -Fix wndows Errors -check your network properties and status

Your monitor is failing due to age.

Either the cord isn't hooked up, a pin is bent, or the computer isn't sending a signal. In the last case, you may need a new graphics card.