20 Most Recent
Aiwa F2000 20" TV - Page 9 Questions & Answers
TV Code for Aiwa TV
If you mean the code for a universal remote then look on the manufacturers web site and it will no doubt be listed
First on tv ok then press stnd by not start
Good day!
please check the B+ voltage if you have 100-115vdc if don't have look for the regulator (transistor)at the power supply section and horizontal output if it is shorted.
if you have B+ check the voltage of horizontal output (base) if have 5vac that comes from the jungle i.c.check the jungle to the base and replaced the defective parts that pass through.
Thank you and good luck.
Need instruction manual for Aiwa RC-AVR03
RC-AVR03is model number of remote control of Aiwa VCR and is does not have any separate instruction manual, post your Aiwa VCR model number (would be written at rear of VCR) to provide you instruction manual copy.
Thanks.
Aiwa tv-14ST3 horizontal output always shorted
Hello
If horizontal output gets shorted always, something may be wrong with Line Output Transformer [LOT], or deflection yoke. If LOT windings inside is short, hrozontal output transistor will get overheated, and will be get shorted soon. If there is winding short in the Deflection yoke, even a sinlgle winding gets shorted, it puts a great load on LOT, which in turn effect horizontal output transistor. The third main reason for horizontal output transistor failure is due to an open or dry solder at the capacitor connected to its collector to negative It will be usually 2500pf to 3500pf, according to the TVs screen size. You just check these three and be sure about the fault.
Ok.
Aiwa GX1100 VCR
When safe show on the screen, it actually means that the child lock feature is on.
All you have to do is press the child lock button again on the remote and it should flash "OFF" on the screen.
Hope you have the remote :)
I lost my original remote
Hello,
what's the name/make and model of the remote?
Without me knowing the type of universal remote, there is no way I can get the right code for your TV.
I look forward to your reply.
Bye for now.
WIRING DIAGRAM FOR HOUSE
I think you mean a grund fault interrupter type breaker or receptacle.
The ground fault breakers fit into a regular box and they snap over the HOT input power tab like miost breakers AND they have a white pigtail wire that connects to the neutral bar in the panel.
The branch circuit that is fed from this breaker has BOTH the hot and the neutral connecting to the breaker as the breaker has two terminals for the purpose. The grounding wire of the branch circuit still goes to tthe ground bar in the panel.
For a GFCI receptacle, the branch circuit feeds the terminals labeled "LINE" and if other receptacles are to be protected by this device, they have their circuits continued from the terminals on the receptacle labeled "{OAD".
Cannot remove tape from machine
take top of vcr and you will see a motor and cogs on one side keep turning until tape comes out if tape armes move out towards head then turn other way
No power
thank you my friend for writing us. in this situation i would do several steps. i would first check the ac outlet by using a lamp or another appliance to see if it is ok. if it is not check the breaker box. if it is good, then check your cord coming from the set visually to see if there are any breaks or if the cord has good connection to the set. you can also wiggle the cord to see if there are any breaks in it. if that proves fine then i would check the fuse to see if it is blown. i would also check the bridge rectifiers, the main filter, the b+ fuse. these are just a few starters to get you on the right track. it can be complicated when dealing with a dead chassis. i hope this solves your problem please rate my solution. thank you.
On TV, I do not have video signal suddenly.I have
Check that the scart cable (if there is such that you used) are operating properly and that there is no gap in it. Try switching cables and see if it works better. Check that no parts of the wire stuck in the input / output of the TV or VCR. //David
The television once on has good picture then black
look for the vertical section of the printed circuit board.there is a vertical driver ic and it is maybe bad...... either the soldering,or the ic.
if you bang on the tv and the picture regains deflection,there is a bad solder joint or connection.
there are a few capacitors too 100mf 25 volt 4.7 50v also 22mf at 50v
Over heating vertical ic
It is quite normal for the vertical ic to be hot. That is why it is mounted on a heatsink. My question is......are you saying you have intermittant horizontal lines at the top? Or occasionally after warm up you experience one horizontal line across the center? Your vertical IC may need to be resoldered. In this case you will have to decide to just resolder or solderwic the solder around the seven pins, clean with flux remover, wipe dry and reapply new solder. If you have (in most cases) White horizotal lines across the top, you need to replace the capacitors next to the ic. Correct polarization on the caps are neccessary. And dont forget to solder the ic as well. And any ground you may find along the way please resolder. Take two aspirns and call me in the morning!
Not finding what you are looking for?