20 Most Recent Alpine CVA-1003 Car Video Player - Page 2 Questions & Answers

The cable that alpine offers now is for 2006 and up models. I checked to be sure....Its the KCE-422i. Your model is not mentioned on the sites. But...you should be able to run it through an input to RCA. Im not sure if there is any other patch cable made for your model.

what kind of connector do you use ? SCART, RCA composite or S-video ? Looks like cable or connector problem

they always go bad withing a year

try going to the setup up then changing the aux-1 and aux-2 setting to pal. and make sure they are on. do this by holding down settings button. then press the 1, 2, 3, 4, 5, 6 buttons till you get the right one.

If you hear the motor try to run but the screen will not move then the plastic slides inside are most likely cracked and warped. This will make the screen catch on the rough edges. Not sure of the part number for the assembly to replace it but this is what I just found on my unit.

you have the amp remote wire hooked to the power antenna lead instead of the amp wire on the deck otherwise just hook it to a switched +12 volt source. You sure you got a DVD changer instead of just a cd changer

Hi,

Depending on the vehicles wiring itself, Alpine uses the below color coding for its wiring:
yellow – constant +12v such as the positive battery terminal
red – switched 12v such as the accessory terminal of the IGN switch
black – ground which could be the chassis/body ground of the vehicle or the negative terminal of the battery
blue/white - remote trigger for add-ons such as a power amplifier
blue – will activate a power antenna (if present)
white and white/black - front left speaker + & -
grey and grey/black - front right speaker + & -
green and green/black - rear left speaker + & -
purple and purple/black - rear right speaker + & -
orange/white - reverse wire
white/pink - monitor control lead
pink/black - audio interrupt from mobile/cell phones
yellow/blue - parking brake
yellow/black - foot brake

To bypass, the yellow/blue must be triggered negative/grounded. Alternately, it may be easier to use an adapter such as a Peripheral PTR7 (http://peripheralelectronics.com/). In some regions, it is not allowed to operate this unit while vehicle is in motion.

Hope this be of help. Pls post back how things turned up or should you need additional information.

Good luck, kind regards and drive safe.

have u tried running the yellow wire to the brake wire. it is suppoesed to have some power whe n u press the brake. both wires can;t be grounded.

Go to alpine .com and scroll to the bottom of the screen to support.Click on support then type in
cva-1003 and there you will get the manual for free.................................................!

Hi,

A copy of the manual for the Alpine IVA-CV800 is available for download from the company's website. Click on the link to download. It's a 251 pages pdf file,

Good luck and kind regards.

Je ne parviens pas à basculer le GPS en français.Merci

if you have a bypass switch you have to turn it on so that you fool the unit to think your parked and then it will let you access the menu screen

you have to go in to your setup. once in there push the numbered buttons and one of them will change the time.

go to alpine.com and on the search type cva-1003 and then download the pdf manual

i have the same problem can anyone help?

After you remove the outer cover, you can see a small, spring-loaded black arm under the middle of the magazine. Just lightly push it to the side, and the magazine will eject.

Hi lilwoodrow,

Check if you dont have loose cable at the back of you screen this can create problem like your having.

You might have a pinched calbe try replacing it.

1. Mechanical Issue: There might be a mechanical problem with the disc drive or the eject mechanism. It's possible that a part is jammed or not functioning correctly.
2. Dirty or Damaged Disc: If the disc is dirty, scratched, or damaged, the player may have difficulty reading it and thus not ejecting it properly.
3. System Error: There could be an internal error within the player's software or firmware causing it to not recognize the disc properly or to malfunction when attempting to eject it.
4. Power Issue: Sometimes, power-related issues can affect the functionality of electronic devices. Ensure that the player is receiving adequate power and there are no loose connections.

Here are some troubleshooting steps you can try:

• Turn off the player and then turn it back on to see if it resolves the issue.
• Try ejecting the disc using the manual eject button (if available). This button is usually a small pinhole near the disc slot. You can insert a paperclip or a similarly sized object into the hole to manually eject the disc.
• If possible, try using a different disc to see if the problem persists. If other discs work fine, then the issue may be with the original disc.
• Check for any visible obstructions around the disc slot and remove them if present.
• If none of the above steps work, you may need to contact Alpine customer support for further assistance or consider taking the player to a qualified technician for repair.

Se o Bluetooth do seu Alpine CDE-W235BT parou de funcionar ap?s uma falha durante a atualiza??o, pode haver algumas etapas que voc? pode tentar para resolver o problema: 1. **Reinicie o Aparelho:** - Desligue o r?dio por alguns minutos e ligue-o novamente. Isso pode reiniciar o sistema e resolver problemas temporariamente. 2. **Restaurar as configura??es de f?brica:** - Consulte o manual do usu?rio para descobrir como realizar uma restaura??o das configura??es de f?brica em seu Alpine CDE-W235BT. Isso pode resolver problemas causados por configura??es incorretas. 3. **Verifique a vers?o do firmware:** - Se poss?vel, verifique a vers?o do firmware do seu Alpine CDE-W235BT. Se houver uma vers?o mais recente dispon?vel, considere atualizar novamente o firmware, seguindo rigorosamente as instru??es do fabricante. 4. **Remova Dispositivos Pareados:** - No menu Bluetooth do r?dio, remova todos os dispositivos pareados anteriormente e, em seguida, tente parar novamente. ?s vezes, problemas de conectividade podem ser resolvidos removendo e pareando novamente os dispositivos. 5. **Atualiza??es de Software:** - Verifique se h? atualiza??es de software dispon?veis para o seu Alpine CDE-W235BT no site do fabricante. Caso existam, siga atentamente as instru??es para realizar a atualiza??o. 6. **Contate o Suporte T?cnico:** - Se as solu??es acima n?o resolverem o problema, entre em contato com o suporte t?cnico da Alpine. Eles podem fornecer assist?ncia espec?fica para o seu modelo e orienta??es adicionais para resolver o problema. Lembre-se de que mexer no firmware e nas configura??es do dispositivo envolve riscos, e ? sempre recomend?vel seguir as instru??es fornecidas pelo fabricante para evitar danos permanentes ao aparelho. Se voc? n?o se sente confort?vel fazendo isso por conta pr?pria, procurar ajuda profissional pode ser uma op??o.