20 Most Recent Alpine CDA-9807 CD Player Questions & Answers

I assume you want to know which color wires are what from the factory stereo to hook up the Alpine which you have the wire colors for?If you call a Ford dealer,they normally will provide the information for free.I googled a couple of sites but the minimum they want is $14.Good luck! Greg

hi david, check out the connection of the yellow and red wires on the back plug. yellow must be connected to a direct battery positive line(continuous positive), the red must be connected to a live wire from the ignition switch OR from a point that is +12v live once the car is started(switched positive). also make sure that that the ground connection is a direct good connection to the body of the vehicle!! make sure that the remote wire(blue) is insulated if you not using an automatic aerial or external amplfier. good luck.cheers.

there is no code for that radio. what exactly is the problem with it? if it is not turning on, make sure you are getting power to both the red and yellow wires. red is switched (ignition) and yellow is constant.

If you can get it apart enough to see the circuit board of the display, you will probably see bad solder connections on the lamps. personally, Ii'd visit a junkyard for an exact replacement stereo. If the one you get doesn't work, they'll gladly find you another.

It does sound like a bad connection on one or more backlight lamps. Aafter removing stereo, you'll probably see several screws and plastic catches holding the face on, then more small screws and catches and connectors you'll have to deal with in order to get it apart enough to get to lamps. Also, they don't want to go back together easily, so what i'd do visit a junkyard and replace whole stereo with exact model.

Hope helps.

Hello! In clock priority mode...Press and hold the Disp/Title button for 3 seconds, The time indicator will blink...Turn the Rotary/Encoder to adjust the hour...When hour is set, turn the Rotary/Encoder to adjust the minutes...Time is set for 5 seconds after the minute...

Guru............saailer
I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

try either pressing the reset switch (if there is one) or disconnecting power to the deck.

Its probably your wiring harness that came with the stereo. Which can cause many more problems. alpine changed their wiring harness around that time. But they used the same plug, just wired different. So now there are crossed wires, but the plug fits, causing the amp chip to fry. maybe even further than the amp chip. an amp chip replacement runs about 80$ at a repair shop. if its just that.

hi

Try to set the cd function to settings! or menu, maybe you have not fair settings in your unit!

Thanks!

Red is ignition
Yellow is constant hot
Black is ground
Gray wires are front right
White wires are front left
Green wires are rear right
Purple wires are rear left
Blue is power Ant if equipped
Orange is ilumm

Make sure you use the proper wiring harness for your vechile.

Hope this helps

it seems like you connected the wrong remote wire to the amp.
Alpine has two remote wires.
BLUE (only) This is the pwr antenna remote wire,every time you insert a cd this remote wire,the pwr cut out.
BLUE/WHITE STRIPE This is the AMP REMOTE WIRE,THIS IS THE REMOTE WIRE THAT YOU NEED TO CONNECT TO THE AMP
LET ME KNOW IF IT WORKS
thank's

What type of vehicle is it in? Some manufacturers, such as Toyota, use separate antenna plugs for AM and FM that cannot be plugged into an aftermarket unit at the same time.

1. Mechanical Issue: There might be a mechanical problem with the disc drive or the eject mechanism. It's possible that a part is jammed or not functioning correctly.
2. Dirty or Damaged Disc: If the disc is dirty, scratched, or damaged, the player may have difficulty reading it and thus not ejecting it properly.
3. System Error: There could be an internal error within the player's software or firmware causing it to not recognize the disc properly or to malfunction when attempting to eject it.
4. Power Issue: Sometimes, power-related issues can affect the functionality of electronic devices. Ensure that the player is receiving adequate power and there are no loose connections.

Here are some troubleshooting steps you can try:

• Turn off the player and then turn it back on to see if it resolves the issue.
• Try ejecting the disc using the manual eject button (if available). This button is usually a small pinhole near the disc slot. You can insert a paperclip or a similarly sized object into the hole to manually eject the disc.
• If possible, try using a different disc to see if the problem persists. If other discs work fine, then the issue may be with the original disc.
• Check for any visible obstructions around the disc slot and remove them if present.
• If none of the above steps work, you may need to contact Alpine customer support for further assistance or consider taking the player to a qualified technician for repair.

Se o Bluetooth do seu Alpine CDE-W235BT parou de funcionar ap?s uma falha durante a atualiza??o, pode haver algumas etapas que voc? pode tentar para resolver o problema: 1. **Reinicie o Aparelho:** - Desligue o r?dio por alguns minutos e ligue-o novamente. Isso pode reiniciar o sistema e resolver problemas temporariamente. 2. **Restaurar as configura??es de f?brica:** - Consulte o manual do usu?rio para descobrir como realizar uma restaura??o das configura??es de f?brica em seu Alpine CDE-W235BT. Isso pode resolver problemas causados por configura??es incorretas. 3. **Verifique a vers?o do firmware:** - Se poss?vel, verifique a vers?o do firmware do seu Alpine CDE-W235BT. Se houver uma vers?o mais recente dispon?vel, considere atualizar novamente o firmware, seguindo rigorosamente as instru??es do fabricante. 4. **Remova Dispositivos Pareados:** - No menu Bluetooth do r?dio, remova todos os dispositivos pareados anteriormente e, em seguida, tente parar novamente. ?s vezes, problemas de conectividade podem ser resolvidos removendo e pareando novamente os dispositivos. 5. **Atualiza??es de Software:** - Verifique se h? atualiza??es de software dispon?veis para o seu Alpine CDE-W235BT no site do fabricante. Caso existam, siga atentamente as instru??es para realizar a atualiza??o. 6. **Contate o Suporte T?cnico:** - Se as solu??es acima n?o resolverem o problema, entre em contato com o suporte t?cnico da Alpine. Eles podem fornecer assist?ncia espec?fica para o seu modelo e orienta??es adicionais para resolver o problema. Lembre-se de que mexer no firmware e nas configura??es do dispositivo envolve riscos, e ? sempre recomend?vel seguir as instru??es fornecidas pelo fabricante para evitar danos permanentes ao aparelho. Se voc? n?o se sente confort?vel fazendo isso por conta pr?pria, procurar ajuda profissional pode ser uma op??o.

Question edited for clarity. https://www.google.com/search?q=alpine+vie-x077+wiring+diagram https://www.google.com/search?q=alpine+vie-x077+installation+manual ..

After researching, it appears that there is no direct evidence suggesting that the Alpine TDM 7543 stereo unit has the ability to switch from green to red lighting. This is an older unit and specific information can be challenging to find. Your best option to get a definitive answer may be to directly contact Alpine's customer service or refer to the original instruction manual.

Help here https://www.google.com/search?q=hange+the+language+of+my+alpine+car+stereo+(700w)+to+English ..

I found wiring diagram at 2000 Dodge Ram 1500 Stereo Wiring Diagram ' Dodge durango, Dodge dakota, Dodge ram 1500 (pinterest.com) and wiring color codes at 2000 Dodge Ram Pickup Car Stereo Wire Colors and Locations (the12volt.com) but I recommend to consult an auto electrician for authentic connections.

ck here.. http://forums.pelicanparts.com/porsche-911-technical-forum/116178-alpine-tdm7543-head-unit-removal.html