20 Most Recent Tylo SUPER SPORT-U8 Sauna Heater 8 kW - Page 4 Questions & Answers

I have same issue, reading 103/104 but barely 80 degrees. Im guessing tstat went bad how can the gfi plug cause this? are you referring to the actual gfi plug for outlet?

Eontact them direct. This is an unknown, undocumented fault but am guessing EE is Electrical Error.

Suite Collection - Owner's Manual PU2 - Dream Maker Spas

https://dreammakerspas.com > uploads > 2019/02 PDF Always keep an accurate thermometer in the water because your spa's thermostat may be in error. Use a high quality, shatterproof. Missing: EE ‎' Must include: EE

• Resources for DreamMaker Spas owners

  https://dreammakerspas.com > owners Nov 11, 2022 - Find resources for Dream Maker Spas hot tub owners: technical videos, Dream Maker Spas Manuals, warranty information and more.

• Cabana 2500L Suite - DreamMaker Spas

  https://dreammakerspas.com > Shop Recline in the deep contours of the Cabana 2500 and experience all the all inclusive suite spa where everything is included.

You need to remove the impeller 1st.....there is usually(not familiar with your particular pump) 2 sets of exterior accessible bolts. One set separates the front and rear of the pump(where the impeller is), and where the motor meets the pump(where it sounds like you have). https://www.youtube.com/watch?v=mpJLp3oWDGU I hope this helps.

limited info generic answer need a multi-meter to test circuits usually heater failure or pump failure but the relays and circuits can get critters or condensation damage

possible heat element bad or temp sensor

possible bad temp sensor

Hello quick question I just bought the same exact Suana today. Does it take a long time for it to heat up .?

If this is an outdoor spa near trees, its almost a guarantee that the impeller is blocked with debris (pine needles can cause this in a hurry)

If the impeller is clean of debris and this is still happening, replace you pressure/flow switch.

if the heat light comes on but doesnt heat bad heater element if red heat light doesnt come on need new temp sensor

https://www.frombytestobits.com/product/bestway-lay-z-spa-water-flow-sensor-repair-kit/ https://www.frombytestobits.com/product/bestway-lay-z-spa-water-flow-sensor-paddle-and-pin/

All the manuals are here Riley. https://www.google.com/search?q=morgan+spa+owner%27s+manual

How to lock and unlock your keypad? - Tubs Parts

https://www.tubs.parts > how-to-lock-and-unlock-your-... Locking: Press and hold the "Down", "Scroll" and "Up" keys simultaneously. The LCD screen will display "Hold the keys to activate the lock". Keep holding down ...

Not much info here but SL could be the mode setting. Typically modes are SLEEP, ECONOMY and STANDARD. Standard maintains your set temp at all times even if it has to turn on outside of normal filtration cycle. Economy only heats during a filtration cycle, and sleep will only heat within 10 degrees of set temp and only in filtration cycle. This cycle is really only useful while going on vacation or other extended periods of non-use. Not sure how to help change modes without knowing what spa pack you have but you should be able to find the owners manual on line with a little research.

possible debris in air inlet

check circulation pump possibly overheating and shutting off

Sort of :>) https://www.google.com/search?q=replace+the+filter+pump+relay+switch+on+Aqualink+RS ..

check gas pressure if ok check burner tubes for bolkages

possible clogged filter or pressure switch bad or circulation pump bad

with power disconnected take off cover take off heater leads (remember where they go take a picture ore write a note if you turn it on and doesnt blow fuse its a bad heater element

It could be a clogged pump basket, impeller, pipe, or skimmer basket. It could also be a closed or broken valve before the pump. In some cases, the pump may have an air leak and is drawing in more air than water. This can reduce filter pressure (and filtration ability).