HEAD LIGHTS I WANT TO TAKE OFF THE HEADLIGHT THERE ARE TWO SREWS ON TOP BUT THERES SOMTHING IN BOTTOM THAT IS STILL HOLDING IT BUT I CANT SEE WHAT IT IS. THANKS

Check the fuses first, then if they are ok you may have a defective headlight switch, they connectors can get burned and the switch contacts as well this can cause the loss of lights like you have. Replace the headlight switch and connector as one repair, do not crimp connect the repair connector on, solder and shrink tube the solder joints. To remove the headlight switch for inspection follow these directions.
Remove two bolts under the radio and pull out that bezel

Remove four 9/32 bolts (or screws seen vehicles with bolts, some with phillips screws, some hex screws) on the very bottom of the panel by your knees (two hidden under the hood release handle)

Remove two bolts right behind the top seam of that panel under the steering wheel holding the top panel to the dash (you should be able to pull the steel panel by your knees down slightly to get to them, but you may need to remove or loosen yours, depends on if someone has had it off before)

Remove the three bolts holding the top cover inside the upper lip by the instrument cluster then you can remove the dash panel holding the switch

Left the bonnet behind the headlight Remove the head light dust boot and the head light connector then there is a spring type clip holding headlight globe unclip it the fit new globe reclip the spring clip and fit the connector and dust boot

The headlights are super easy to replace, there should be just a couple 10mm bolts of maybe t20 torque srews at the top of the lights take them out and the headlight should fall out.

theres phillips head screws all around the top and bottom of light, should be two on top two on bottom
remove those and light comes right out
install new light
re install screws
and viola new light
happy motoring

Behind the headlight assembly is a large weather boot. Grasp the small portion that the wires come into and pull it straight out to remove the wiring harness. Grasp the large weather boot from the bottom and pull it up. Work your way around the rim and remove it. Yank it off the headlight bulb.

You should then see the headlight bulb and a large wire holding it in place. At the bottom of the assembly is a clasp that holds the wire in place. Work the wire out of the clasp and pull it all the way up.
The headlight should now be free and able to be removed. Remove it and replace it with a new one. Align the three tabs of the bulb accordingly; you'll see two of the slots for these tabs at the bottom, the third is at the top. Make sure that the bulb is inserted completely underneath the wire hold-down. This hold-down is required to keep the bulb from moving around. Ensure that you do not touch the bulb with your bare fingers.

With the bulb inserted, push the wire hold-down down into place and lock it into the clasp. Push the large weather boot back on, taking note of the "TOP" label. Push the center portion of this boot around the back of the headlight bulb.
Reinstall the wiring harness and test the light.

check the headlight grounds
also check the daylight running light module

two clips hold the headlight in place at the top...remove these and the headlamp will move forward enabling you to replace the halogen bulb (9007 at CTC)

Raise the headlights, either with the switch or manually by turning the knob on the headlight motor counter-clockwise.
Unplug the lights NOW to avoid an accidental closing on your fingers,
Remove the 3 philips screws holding the black plastic surrounding the headlights, and slide it forward, there is a small clip on the top that helps hold it to a corresponding clip at the top of the headlight,
Look inside the cavity and you can see the 5 nuts/bolts ( 6 on later years ) that need to be removed,
If you are on the driver's side you can now remove the whole assembly, on the passenger's side you must first unplug the headlight door control module.

THE TOP SCREWS ARE EASY. THEN THERES THE BOTTOM OF THE GRILL. REMOVE PARKING LIGHTS. THERE ARE 3 PLACES AT THE BOTTOM OF THE GRILL THAT HOLD IT. THERE ARE NO SCREWS OR BOLTS TO REMOVE. JUST 3 PLACES WITH PUSH BRACKETS. LEFT, RIGHT AND CENTER,,A LITTLE TRICKY BUT DONT GIVE UP. LIFT AND PULL THESE TABS/BRACKETS. THE BOTTOM CHROME SHOULD COME OUT A TAB AT A TIME. YOU WILL DO GOOD,,,,RIGHT? YES

The plastic cover comes off over the top of the head lights when you have the hood open, the adjustments are there. The screws are small.