How to remove and install drivers and pasenger airbags

You cannot remove it unless you replace the airbag. I have the same thing on my drivers airbag. You will still pass inspection with the drivers airbag not working. To get the airbag replace, you are looking at about 3 grand, I just put a dark sticker over my airbag deployed light because I got tired of looking at it The airbag will not cause other problems for you. Just cover up the light and forget about it.

Could be a wiring problem or the clockspring in the steering column.
You would need to pull the steering wheel and test the circuits.

you have to remove your drivers seat, get a knife, very kind remove a fittings of your airbag, then go to your dealer buy a brand new airbag, get a niddle fit it all, and make all the procedure with airbag replacement. thats all

This process would very depending on each car. Check the fuse box for the airbag fuse. Have it removed before disassembling the airbag assembly. For the driver side airbag... remove the cover of the driver's wheel to gain acces to the assembly. In some cases you will have to remove the cover of the steering columns. For the passenger side airbag you need to remove the dashboard to gain access to the assembly.

1. Open hood, disconnect and isolate the battery negative cable.
2. Wait two minutes for the system reserve capacitor to discharge before beginning any system or component service.

Instrument Panel Trim - Remove/Install

1. Remove the steering column opening cover two retaining screws and unsnap cover from instrument panel.

Knee Blocker Airbag - Remove/Install

1. Remove four knee blocker airbag retaining bolts from airbag.
2. Pull down knee blocker airbag and disconnect the one electrical connector.
3. Remove knee blocker airbag from vehicle. Here

REPLACING CRUISE CONTROL SWITCH

1. Disconnect and isolate negative battery cable from battery.

2. Remove airbag module (See AIRBAG REMOVAL below).

3. Remove speed control switch mounting screw and remove switch from steering wheel.

4. Reverse procedure to install.
AIRBAG REMOVAL
1. Disconnect and isolate negative battery cable from battery.

2. From the underside of the steering wheel, remove the two screws that secure the driver airbag to the steering wheel armature.
CAUTION: The horn switch and the clockspring pigtails connected to the back of the airbag module are fragile. Do not pull on these wires to disengage them. These must be handled carefully to prevent damage to the horn switch and/or the clockspring assembly.
3. Pull the driver airbag away from the steering wheel enough to access the three electrical connections on the back of the airbag housing.

4. Disconnect the steering wheel wire harness connector for the horn switch from the horn switch feed pigtail wire connector, which is located on the back of the driver airbag housing.

5. The clockspring driver airbag pigtail wire connectors are secured by integral latches to the airbag inflator connector receptacles, which are located on the back of the driver airbag housing. Depress the latches on each side of the connector insulator and pull the insulators straight out from the airbag inflator to disconnect them from the receptacles.

6. Remove the driver airbag from the steering wheel.

7. Reverse procedure to install.

if you deactivate and a pasenger is injured in any accident,you will be liable for serious damages.if its for a baby seat,then take a tip and put the baby in the back with an "isofix" seat (see isofix webpage) you have to remove the whole explosive device to deactivate.

The pasenger side window button may be bad or wire hornest that runs from pasenger side kick panel in door jam, to the inside of the door. open passenger side door there will be a rubber boot between the door hinges.pull the rubber boot back and check for broken wires.

to disable them,unplug the plugs after the battery has been disconnected for 2 minutes to avoid deployment. if you physically want to remove them,that is different,the one on the passenger side is part of the dash,a thin plastic line ruptures upon deployment and the airbag inflates.
the drivers airbag is disabled by the yellow connector at the bottom of the steering column

You would be well advised to leave anything/everything associated with any airbag issue to the dealer. Safety issues. . .