My 1995 Toyota 4 Runner does not have a front windshield washer reservoir. Where should it be located? My rear window washer does not work also. Where is the rear reservoir located?

Any idea what vehicle you drive?

not 100% on this, but typically, you have to open the back hatch, and there will be a small rubber cap over the opening for the washer fluid located on or near the top of one of the taillight lenses on either side of the vehicle.


I’m happy to help further over the phone at https://www.6ya.com/expert/adrienne_b03fb46fc6334991

PROBABLE CAUSE Impact to the front bumper pushes the bumper back far enough to break the washer pump hose fitting. CORRECTIVE ACTION Replace the windshield washer reservoir and washer motor with updated parts. REPAIR PROCEDURE 1. Turn the ignition switch to ACC (I) to unlock the steering column. 2. Raise the vehicle on a lift. 3. Remove the right front inner fender. Unhook and pull back the bumper for better access. CLIPS (6 places.) SCREWS (6 places.) RIGHT FRONT INNER FENDER 4. Release the hooks on the upper right side of the front bumper. 5. Remove the clip from the filler neck, then remove the filler neck. FILLER NECK CLIP WINDSHIELD WASHER RESERVOIR CLIP WASHER MOTOR CONNECTOR BOLT BOLTS WASHER TUBES 6. Remove the right front fender trim, and disconnect the washer hose from the 90-degree fitting. CLIP FRONT FENDER TRIM FRONT HOSE 7. Disconnect the 2P connector and the two washer tubes from the washer motor. 8. Remove the washer reservoir clip and the three bolts, then pull out the reservoir. 9. Assemble the new reservoir components, but do not install the filler neck. 10. Trim 85 mm off the end of the 1,260 mm washer tube only. 11. Route the washer tubes on the reservoir. NOTE: The black fitting is for the front windshield nozzles, and the white fitting is for the rear nozzle. 85 mm 12. Install the reservoir. 13. Connect the rear tube to the straight fitting in the wheelwell. 14. Connect the 2P connector to the washer motor. NEW RESERVOIR Connect the rear washer tube. CLIP BOLT 9.8 N•m (7.2 lb•ft) 15. Install the filler neck with the original clip. Connect the front washer tube to the 90-degree fitting. Then reinstall the front fender trim. WASHER FLUID DIPSTICK 2P CONNECTOR FRONT FENDER TRIM FILLER NECK CLIP

The rear window washer gets its feed from the front reservoir. One reservoir feeds both windows.

Yes there are two pumps located in the wiper fluid reservoir. If your in a bind, you can switch the plugs and small hose that go to them because they are both the same. The upper pump operates the back, and the lower pump operates the front. The back won't work until it gets replaced, but it beats driving backwards.

It's the same reservoir as the front windshield washer. If it's not working, check the washer line to make sure there are no cracks or breaks in it. Good luck and keep me posted.

on the bottom of the reservour is a hose which is attached to a little pump which makes the washer fluid shoot out on to your windshield.it also has an electrical plug connected to it.sometimes by wiggling the plug it will start to work again,if not,make sure that there is power going to the pump.if there is power,your washer pump will have to be replaced.if there is no power,check your fuses. hope this information helps you with your problem. take care, manny

check to make sure that the wiper is not stuck in the window seal. Pull it out if it is and then try. The window will not roll down if the wiper is in that position.

bottom rear of the engine at transmission bell housing.

the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal

1. Disconnect the battery ground cable (14301).
   
2. Raise and support the vehicle.
   
3. Remove the RH wheel (1007).
   
4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
   
5. Remove the windshield washer reservoir top bolt.
   
   
6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
   
7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
   
8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
   
9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
   
10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.
    
    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.
    
    
11. Loosen the two windshield washer reservoir side bolts.
    
12. Remove the windshield washer reservoir by sliding it out of the side slots.
    
13. Remove the windshield washer pump.
    
    Installation

To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).