My 1995 jeep rangler want start but it turns over i replace rotar button, plugs, wires, distributor cap it's not getting any fire to the distributor cap

No spark at the coil replace all spark plug wire and coil wire but start with fuel pump first it wont start anyways without fuel id look into a new cap and rotar with the plug wires might get lucky and find a distributor at a wreckers for the same price as cap and rotar

Make sure you have Power to the plug marked BAT on the side cap. If you do its probably the module inside under the Rotor

the timing is off a bit! heres how I do it. remove the number 1 plug, stick a straw or similar in plug hole. turn engine over by the crank shaft with a wrench. when piston gets to very top of bore, just before it goes down. this is tdc. remove distributor cap and remove distributor reposition the distributor rotor button facing number 1 plug wire inside cap. replace cap and try it! please let me know if this works for you. good-day ! if you can not get to number 1 plug. just turn the crank to tdc marks are on damper pully or crank. is this a 5.7,

V6 engine: firing order: 1 2 3 4 5 6, distributor rotates clockwise. Left bank of engine (driver's side), cylinders 2, 4, 6 (#2 at front of engine). Right bank: 1, 3, 5 (#1 at front of engine).
Inline 6 engine: firing order is 1-5-3-6-2-4. Distributor rotates clockwise.
The number one tower on the dist. cap should have a mark or numeral 1 on it. If not, turn crankshaft to top dead center of compression stroke on number one cylinder, the 0 degrees or "T" mark on the crank pulley pointer. If you are on the compression stroke (not the exhaust stroke), the rotor under the dist. cap will be pointing to the number one cylinder spark plug wire tower.

For spark plug problem,click the help links provided below :---Car has no spark?http://schematicsdiagram.blogspot.com/2011/06/car-has-no-spark.html
------------How to Replace Spark Plugs?http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-spark-plugs.html
-------------Car cranks, has spark but will not start?

http://howtobyme.blogspot.com/2011/12/car-crankshas-spark-but-will-not-start.html

------------------------
The spark plug firing order for car?http://schematicsdiagram.blogspot.com/2011/06/spark-plug-firing-order-for-car.html
----------How to gap spark plug ?http://technoanswers.blogspot.in/2012/02/how-to-gap-spark-plug-on-chevy-impala.html-----------Spark plug Replacing for?http://technoanswers.blogspot.in/2012/02/spark-plug-replacing-for-chevy-impala.html
-----------How to identify number one spark plug on the distributor cap?http://schematicsdiagram.blogspot.com/2011/12/how-to-identify-number-one-spark-plug.html
---------How does the spark plug wire go on the distributor cap?http://schematicsdiagram.blogspot.com/2011/12/how-does-spark-plug-wires-go-on.html
---------Spark plug Firing Order Diagram?http://schematicsdiagram.blogspot.com/2011/12/2006-suzuki-forenza-spark-plug-firing.html
-----------This will help.Thanks.

If you have a no spark condition, replace the crankshaft position sensor. Check for engine codes also by turning the ignition key on-off-on-off then leave it on and watch the check engine light blink/flash an engine code.

first thing you need to check your sensor on top of your transmission make sure is connected to get signal to activate the fire

a crank sensor tells the coil to fire.are you getting a signal at the coil to fire?

IS IT THE 4.0L?IF SO U MAY HAVE A BAD CRANKSHAFT POSITION SENSOR.

it might be the optispark harness wire.it starts and runs good. once u turn it off its hard to turn back on?