Question about Cell Phones

1 Answer

I'M moving my kitchen sink and diswasher from one place to another. If the pipes are copper do I need to sotter them or is there another way?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 260 Answers

You have an alternative. You can use copper pressure fittings. Your local hardware store should have them available. You will need to know the exact dimensions of the pipe you are using.

Good luck.


Posted on Jul 24, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a black, conposit kitchen sink. It has salt residue from our water softener system built up on it.

vinegar, or CLR should remove this. I've got the same but never had a problem with salt build up. I also have a magnet coil installed around my water line which allows for minerals to not stick. they brush off once dried. perhaps you need to install something like this?

Dec 03, 2013 | Cell Phones

1 Answer

Need general instructions. They fell between the seat and console in my car! Why is one wire shorter than the other too!

It was manufactured during the great copper crisis of 2010, world reserves of copper hit an all time low and as a result many companies were forced to use shorter wires manufactured from old pennies.

May 04, 2011 | Cell Phones

1 Answer

I am unable to get my Motorola Blue tooth H720 to go on and sink up with my T Mobile Sonny Ericsson phone.

yes it generally happen when different type bluetooth try synchronizing.
try placed them side by side and type right pass code.

Mar 04, 2011 | Motorola Cell Phones

1 Answer

My blitz phone works when the slide is down but when u slide it up the screen goes white even if u slide it back down but the phone and the key board textes ??

hi this is a common problem with all flip and slide phones, what the problem is is that their is a small wafer thin ribbon that goes from the one part of the phone to the other part that moves now over time the little copper wires inside the ribbon ware and break causing the data to not send properly this then gives you the white screen.
Now you can get this repaired and it wont cast that much to repair, the best place for you to goto is a small phone shop you know like a private business and not a big firm, these will often be a lot cheaper as they need the custom.

May 07, 2010 | UTStarcom Blitz Cell Phone

1 Answer

What can i do to repair it after sinking in the water?

This has happened to me before. What I did was I let it dry off from the sun. I placed it in a car, close to the window and waited till it was hot and dry. Then it should work once you turn it on. You don't have to do this, but it has to b in a place where it will get very hot. Hope that helps.

Mar 22, 2010 | Nokia 6500 Slide Cellular Phone

1 Answer

It just says smart chip rejected?

Turn off the phone. Take the battery and sim card out. Make sure there is no dust or dirt of where the sim card goes. Blow air (from your mouth) of where the sim card goes. Then place the sim card back in the phone. Make sure it is in the right position. Copper contacts facing downward. Put the battery back in your phone. Turn it on. See if the smartchip rejected goes away.

If not you may need to contact your Phone Provider Tech Support to troubleshoot and confirm that you may need a PUK Code to register or you may need a new SIM Card, as they do fail from time to time.

Jan 14, 2010 | Nokia 2610 Cellular Phone

1 Answer

I droppedit on the ground now it only works wen its on the charger

The battery could have become dislodged. Verify that it is not loose and that the gold/copper contact points are still in place.

If they are, try replacing the battery or phone.

Dec 10, 2009 | LG enV3 VX9200 Cell Phone

1 Answer

Nokia E65 slider doesent work

there is no micro switch.. but there is sensor intalled... i suggest that you check the ribbon connector it is a thin plastic with copper lines on it...

Feb 09, 2009 | Nokia e65 Cellular Phone

1 Answer

Switchback doesn't charge

I suggest you buy a new battery, if that dosent work, send it back to Virgin Mobile for repair

Apr 13, 2008 | Kyocera Switchback KX21 Cellular Phone

Not finding what you are looking for?
Cell Phones Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cell Phones Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers


Level 3 Expert

66744 Answers

William Alequin

Level 3 Expert

856 Answers

Are you a Cell Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides