Hi.I have a indesit washing machine model W103.It seems to run part way through it's cycle until it needs to drain.The program dial then starts clicking around.Someone suggested that it could be the belt?? But I thought this unlikely as the drum still spins.I have emptied the pump but the problem still occurs.

hi harrison.
see if this link helps you out.
indesit washing machine starts cycle and then after minute stops Google...

Lots of great replies, but I narrowed my "3 beeps" during wash to my daughter putting too much washing in the machine. It seems to have an 'overload' sensor that beeps when it detects too much weight. I initially thought it to be a blocked pump, but noticed it was beeping during washing cycle without the pump running. So worth trying a little less in the machine before you start taking things apart.

hi something similar has started happening to our washer, after the initial wash starts the machine doesn't do anything for a while then the red door light flashes on and off very quickly as does the 1st and 3rd green wash cycle light?

Hi,
The water level will never go above the lower part of the door bowl. Can you be a little more specific on your question?
Regards
Sussex Engineer

I have LG Washing Machine WF-S6607 when I START after 5 Second it will be stop and alarm to come up on Rinse MODE. what I do?

Actually, while the settings dial spins, there is also a kind of grinding/clicking sound from down where the drain port is. I checked it and there is no filter there when I open it.

I've found you need to reset the program cycle for this. It's annoying to lose the soap and conditioner but generally, if you download the manual and follow the reset instructions (which for me also involved turning the machine off at the mains aswell as holding the power button down with the machine on stop setting) it usually works ok.

Pump or hoses still blocked,Or pump has had it,Can supply new pump by post if req.

01 = Acquastop operated due to leak / overfill - machine drains until empty + lmin.

A02 = Heater Relay open circuit/short circuit or Thermistor or Safety T/Stat o/c or s/c or Element machine fills to Level Switch & Wash Pump runs.

A03 = Thermistor open circuit /short circuit - machine drains until Level Switch resets +1minute

A04 = Unable to sense/reach temperature in 70mins. - machine drains until Level Switch resets + lminute

A05 = Level Switch not resetting in within 3' 20" of drain commencing - machine drains until Level Switch resets +1 minute

A06 = Not used see also H20 at end

A07 = Wash pump Triac closed/open circuit - check that Drain Pump is not disconnected or Aquastop operated

A08 = Auxiliary Wash Pump Triac closedlopen circuit - check Wash Motor operation- machine drains until Level switch resets+30"

A09 = Main Wash Pump Triac closed/open circuit - cheek Wash Motor operation- machine drains until Level Switch resets+30"

A10 = Fill Solenoid valve Triac closedlopen circuit - check valve/operation - machine drains until Level Switch resets+30"

A11 = 1/2 load Solenoid Valve Triac or alternating Wash Motor action - check Solenoid Valve operation & alternating Motor action, replace Module if required - machine drains until Level Switch resets +30"

A12 = Relay with open circuit - check Heater, replace Module if required - machine drains until Level Switch resets+30"

A 13 = Dispenser Triac incorrect operation closed/open circuit - Wash Cycle completes but with Dispenser Lid notfunctioning correctly

H20 = Static 'Fill Time exceeding 6 minutes - cheek for blockages/low pressure

Hi there. I have an old model, the indesit WM12. Never counted the flashing light (yours was 10) but my dial started clicking constantly at the drain part. I called Idesit and they told me it was a blockage in the filter.
The filter they speak of it located, on mine, at the front of the machine at the very bottom on the right. It is a black dial about 3 - 4 inches in diameter. Unscrew that anti-clockwise (a real pain because so much water comes out. My wife and I unscrewed it, filled a baking tray with water, screwed it back up, emptied / substituted tray then same all over again - until empty. Though putting it on drain again and again helped at same time). When I pulled out the filter found a 'colour catcher' sheet in it. We used them first time ever the other day. Removed that, gave filter a wee clean and, hey presto, all is working again. Hope that helps. Jim