Question about Kenmore HE2 Plus Front Load Washer

1 Answer

How do I remove the cabinet from mt Kenmore front load washer. It is leaking during the wash cycle.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 999 Answers

Screws along the bottom of the front lower panel. This will get access to find the leak. If it is up high the top comes off with 3 screws at the back top edge and slide forward.
Eric

Posted on Jun 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have kenmore washer. when I open door, I found water in there. So i drain water and washed. After two day, I found same level water in cabinet. I think water leak in side or didn't operate water presure...


If the machine is not pumping the water out during the spin cycle, then it could be a couple of things. First, it could be that the cycle timer is faulty and needs to be replaced, or it could be that the water pump is bad and that needs to be replaced. Either way, the repair is cheaper than a new machine.

Mar 07, 2011 | Kenmore Front Load Washer

1 Answer

Help! Mt Kenmore Elite Quietpak2 HE3 keeps


F/06 Drive Motor Tachometer Error
The control is unable to properly detect motor speed and the machine will shut down. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes.
  • Check wire harness connections between the Drive Motor/Tachometer and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU)
  • Check the Drive Motor
  • Check the MCU
  • Check the Wire Harness

Mar 10, 2009 | Kenmore 3.8 cu. ft. HE3 Front Load Washer

1 Answer

Leaks water


Probably a bad water pump. That is were the Kenmore usually leaks.
2 screws on the top panel right and left sides.
Remove these screws, tilt the control head backwards.
Remove the wiring harhess connector.
Remove 2 clips holding the cabinet to the back panel.
Remove the cabinet by pulling forward.
Pump is attached to front of motor.

Feb 21, 2009 | Kenmore 24642 Top Load Washer

2 Answers

Kenmore Front load washer model 3 970-c29042-00 The washer is making a loud noise and shakes like something is loose when the drum is turning..


I have a kenmore front load washer, model: 417 42042100
It makes loud noise and becomes louder during the spin cycle.
The drum is loose when I inspected through the front door.
My problem is how to open the cabinet and replace any broken parts.

Thanks.

Aug 04, 2008 | Kenmore 46462 Front Load Washer

1 Answer

WASHER LEAKING


DO YOU MEAN THE SPIN RINSE CYCLE OR FILL UP?THE FRONT COMES OFF FROM UNDER THE TOP SEAM,USE A PUTTY KNIFE ON EACH OF THE FRONT SIDES,PUSH IN ON THE CLIP AND PULL OUT ON THE FRONT PANEL,DO THIS ON BOTH FRONT SIDES,LET ME KNOW,THANKS-MIKE

Jun 23, 2008 | GE WBSR3140DW Top Load Washer

2 Answers

Leaking Kenmore elite he3 washing machine


removethe lower acess panel 3 screws across the bottom , run the cycle and watch to see where exctly the leak is coming from it should be quite apparent

Mar 09, 2008 | Kenmore 3.8 cu. ft. HE3 Front Load Washer

2 Answers

Kenmore series 70


  The whole cabinet comes off on this washer.  Too remove you need to remove 2 screws in console.  These may be in back on the right and left ends of console or may be in front on each end.  If you can-not find them they might be hidden under plastic end trim.  They are located in front of console on both ends.  To remove pry them up from the inner lower edge and peel towards outside of washer.  Then remove screws and shake console back and forth while pulling up.  Console will hinge back.
   Remove to gold colored clips with screwdriver prying at front.  Make note of the position of these clips.  Unplug lid switch harness and pivot cabinet back and off.  The usual spot for a leak is the pump.  Check for stain coming from area on pump where motor shaft enters.  The pump can be removed by taking off the 2 clips.  Also check small diameter hose that enters side of wash tub in back side.  Make sure this is attached to tub. 

Oct 14, 2007 | Kenmore 22422 Top Load Washer

Not finding what you are looking for?
Kenmore HE2 Plus Front Load Washer Logo

Related Topics:

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal DeAngelo

Level 3 Expert

2122 Answers

fordexpert

Level 3 Expert

5495 Answers

Mike Carew

Level 3 Expert

969 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...