Machine won't turn on flashes dL F code and gives me short buzzes

The capacity of the Whirlpool Duet GHW9300PW4 front-loading washing machine is approximately 4.3 cubic feet. This is a standard capacity for a front-loading washing machine, and it should be sufficient for most households.
It is always a good idea to refer to the manufacturer's specifications or the manual for your specific model of washing machine to get the most accurate information on capacity and other features.
I hope this information is helpful. Let me know if you have any other questions or if there is anything else I can assist with.

Dl is door lock f what provide full model number please

The machine is not starting because the door lock fails to lock the door as what error code FdL stands for. It flashes after the door locking routine fails to lock the door after 6 attempts. Replacing the door lock/switch assembly is the only viable if no problem is seen with the wire harness connecting the assembly to the central control unit. The link below contains the detailed instructions in replacing the door lock/switch assembly.

Replacing the Door Lock/Switch Assembly on Whirlpool Duet and Kenmore Elite Washers

This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

usually whirpool duet models come up with the error codes with "F" followed my a number..... can u clarify if its just "F" or has a number next to it... it wud help us provide us better solutions to u.....

It is saying there is a problem with your door Lock. when you close the door does it hold like it use too? try to open and close the door if it doesn't really close properly then you will just need a door latch. If the machine gives you an f11 code then its the main computer board that can also give your the door lock error. I would check the door first though.

Check out my wesite http://www.fixya.com/support/t364216-whirlpool_duet_ht_ghw9400pl0

Try everything else, like reseating the connectors, then look here:

http://adsisecurity.com/KenmoreWasher.htm

I have a whirlpool duet washer i can't retrieve the model number because the door is locked but the dryer which is the match to the washer is model number GEW9200LW. My question is that when I hit the control button then start, a muttled beep will sound not allowing the door to open. I get an error message of DL then it flashes to F? Any help?

machine controls may be locked. Power on the unit and hold in the far right button for 4 seconds and then try to select settings and cycles