Vm9312 I m able to get ride off blue screen. but i m not able to acess the sercet menu. even after i pass stop twice and then press 1,2,6,4. i had vm9312 twith touchscreen. i need help to access the sercet menu. rav.

1. Make sure your Jenser VM9312 is on, and select AM/FM as your source.
2. On your remote, press the Setup button, located on the lower right of the remote, you should hear a beep from your VM9312 when you press the button.
3. Now, making sure you hear a beep after every key press, press, 543210.
4. If you did this correctly, a new menu screen will pop up.
5. On the display, press the hammer and screwdriver icon, located on the left hand side of the screen.
6. Next press the menu line for brake override, a sub menu will appear.
7. Select ON.
8. Press the X at the lower left of the screen.
9. Enjoy, and please drive safely, for a ticket is one thing, but a fatal accident you have to live with is forever.

Here is the code:
I did this with the remote
Press stop twice(which is also the BAND button)
Press 1,2,6,4
Press down 1 time(button below the Play/Enter)
Press Play/Enter 1 time
(You should now see the menu)
Brake override should say No
I was told to change macrovision to No
Hit sys setup twice to save and exit
Hope it works like mine did!

You can try the procedure for the VM9311TS model (the one I have) - I don't know if it'll work but it's worth trying. Put in a DVD, and let it start playing. Then hit STOP on the remote twice, and enter the code 1264. If you were able to see the actual movie at this point, you'd see a menu pop up. Push down twice, then ENTER. At this point the blue screen should clear and you should see the movie itself. You'll have other options on that menu, like a macrovision option to allow you to see burned DVDs. Set what you like, then on the remote, hit SYS SETUP twice to lock in your choices.

Insert the DVD

After the disc loads and plays you will see a blue screen telling you "it is unlawful to drive with a movie blah blah blah"

1)Activate the brake sequence and disable the blue screen using the hand brake, the switch method or anything else to give the unit its three pulses to disable that freakin blue screen.

(What I did was I installed my radio entirely, then took the pink wire and touched for two seconds, removed for two seconds and then touched and held the negative pole of a mower battery laying on my passenger seat until the screen was no longer blue.)


2) Next, on the main remote press stop twice, then 1, 2, 6, 4.

You will now see a hidden menu that says:

Region Code
Brake Override (I know you're drooling by now)
Macrovision (Watch all the burned and pirated movies you want if this option is off)
Loader Version
Model Version


3) Using the right joystick on the unit, navigate to the options of your choice, click on them to toggle on, off or which region code you want.

This is what you want:

Region Code: 1
Brake Override ON
Macrovision: OFF

When your done, click SYS SETUP on the main remote TWICE to save the settings and bingo, your done!!! Hooray!!! You can now kill your whole family in the car while watching that adult movie while your driving.....


The other way of doing this is by not engaging the parking brake sequence, thus you're inputting the code blindly.

1) Insert the DVD and you'll get the blue screen.

(If you have more than one tv, the unit itself will have the blue screen but the additional tv's you have plugged in will NOT, they will show the dvd menu. Thus you will be able to see the hidden menu on the additional screens after inputting the code, but not on the main unit because of its blue screen.)

2) On the main remote, push stop twice and then 1, 2, 6, 4

3) Push the joystick on the unit SOUTH twice and then click it once.

4) Press SYS SETUP on the main remote twice to save your settings.

You can get into the master system by using your remote. 1.Make sure your Jenser VM9312 is on, and select AM/FM as your source. 2.On your remote, press the Setup button, located on the lower right of the remote, you should hear a beep from your VM9312 when you press the button. 3.Now, making sure you hear a beep after every key press, press, 543210. NB:If you did this correctly, a new menu screen will pop up. 4.On the display, press the hammer and screwdriver icon, located on the left hand side of the screen.
NB: Here you can bypass the break and regions etc. When done Press the X at the lower left of the screen and enjoy.    

Just go to the set up menu ( Your screen should say setup at the upper center of your screen ) Then press 5, 4, 3, 2, 1, 0 with your remote control and a second menu will apear, on your left side press the second option and select parking bypass to on.

You can try the procedure for the VM9311TS model (the one I have) - I don't know if it'll work but it's worth trying. Put in a DVD, and let it start playing. Then hit STOP on the remote twice, and enter the code 1264. If you were able to see the actual movie at this point, you'd see a menu pop up. Push down twice, then ENTER. At this point the blue screen should clear and you should see the movie itself. You'll have other options on that menu, like a macrovision option to allow you to see burned DVDs. Set what you like, then on the remote, hit SYS SETUP twice to lock in your choices.

1) Insert the DVD and you'll get the blue screen.

(If you have more than one tv, the unit itself will have the blue screen but the additional tv's you have plugged in will NOT, they will show the dvd menu. Thus you will be able to see the hidden menu on the additional screens after inputting the code, but not on the main unit because of its blue screen.)

2) On the main remote, push stop twice and then 1, 2, 6, 4

3) Push the joystick on the unit SOUTH twice and then click it once.

4) Press SYS SETUP on the main remote twice to save your settings.


It may take a few tries but you'll get it. This method can be done if you don't want to bother temporarily activating the brake sequence, but if you only have the unit and no additional tv's, its #$%^&* damn hardbecause you can't see the settings your changing.

This is the way to do it without engaging the parking brake sequence, thus you're inputting the code blindly.
1) Insert the DVD and you'll get the blue screen.
(If you have more than one tv, the unit itself will have the blue screen but the additional tv's you have plugged in will NOT, they will show the dvd menu. Thus you will be able to see the hidden menu on the additional screens after inputting the code, but not on the main unit because of its blue screen.)
2) On the main remote, push stop twice and then 1, 2, 6, 4
3) Push the joystick on the unit SOUTH twice and then click it once.
4) Press SYS SETUP on the main remote twice to save your settings

This is the way to do it without engaging the parking brake sequence, thus you're inputting the code blindly.
1) Insert the DVD and you'll get the blue screen.
(If you have more than one tv, the unit itself will have the blue screen but the additional tv's you have plugged in will NOT, they will show the dvd menu. Thus you will be able to see the hidden menu on the additional screens after inputting the code, but not on the main unit because of its blue screen.)
2) On the main remote, push stop twice and then 1, 2, 6, 4
3) Push the joystick on the unit SOUTH twice and then click it once.
4) Press SYS SETUP on the main remote twice to save your settings