DUAL XDVD700 BYPASS

The way you bypass the E Brake is you have to ground the wire to the radio sleev itself. There are two different peices. The radio itself and the sleeve that holds the radio in place. Take the yellow wire (the ebrake wire, not the yellow ignition wire) and open the metal connector up just slightly. Attach that wire to the top of the sleeve on 1 of the teeth located near the front of the unit. You have to make sure that the connection is good or it will not ground. Next slide the clear plastic over the wire so the only connection is with the tooth.
Then Insert a cd or dvd in the player. Press play on the remote and then push stop 2 X times on the remote. After you have done that press 26604 on the remaote and then press enter. This will permanently unlock the parking brake feature and allow you to watch dvds while in motion. If you need any further help you can eamial me.

The XDVD700 by dual is the easiest ebrake bypass to do. Take the yellow ebrake wire and connect it to a ground or connect it to a ground or the same ground as the dvd player itself, both will work fine. 100% functional, it doesn't change anything except for the fact that you can watch the dvd while in motion. Do not waist your time with those bs codes that never work, and if they do they work for about half a movie

You can solve this problem by hitting menu on the remote go to set up and turn the video out on. When you put in a DVD it will show you the blue screen still, but will go black hit the mode button twice on the remote and you should see a picture. It may go black one more time just hit the mode button once more and you can watch your movie. These are safty features that come on this player due to it being illegal to watch a in dash DVD player. Hope this helps...

Ok when i open my screen it says put a password??? last time i open it it sayed tha same thing but dis time it had a pop up number pad n i put in 0000 thts the code now whn its open its says 2 put in password but no pop up pops up its like froze i can listen 2 nothing or take my cd out lol... wht can i do whts the problem can u help me

If you want you can do the same as i did. Buy a toggle switch and ground one end out to the chassie of the body and the other end up to the ebrake and find a disclosed place to place it so that it isnt visible. When you have installed it open up the audio menu while you have dvd in click the toggle switch for one second then click it again off for a second, back one for a second off for a second. Then back on it will come on with the movie showing.

To play dvds on th road.... take the wire from the e brake and hook it to a ground.... when you put in a dvd you will see the blue screen that says dont drive with dvd bla bla bla...... take the e brake wire that is connected to a gound disconect it touch once touch twice and reconnect within five sec you should see the picture if not repeat this step..... Its the wire that says connect to e brake. just hook to a ground and do the double touch and leave connected to bypass the saftey

If you put a movie on an ipod the go to video setings on the ipod and turn video out "ON" then when conneted to xdvd700 there will be a little movie button in the top right conner when listing to music with the ipod press that then select the movie on your ipod its self then the movie will show up on the xDVD700

Being a radio shack man myself this is real easy to do.
All you need to do is go to radio shack and buy yourself a 12 volt or above momentary push button/switch (about $3) If the button swith/button comes with wires then just connect one end to the emergency brake wire from the radio and then connect the other wire from the switch to a ground to your car. You can use the same ground connection that you used for the radio and it will be fine. make sure you wrap up the wires to prevent shorts.
Also make sure that the switch that you buy can be mounted because you will need to use it every time you want to use the dvd.( you might need to drill a small hole for the switch depending on what you buy)Make sure you have enough wire so you can mount it where you can easily use it like under your steering wheel.
When you are ready to use the dvd put the dvd in the player and after a few seconds the screen will turn blue and the message to "Set the emergency brake" will come on. Now just press the switch/button for one second and release it. The screen takes about 6 second to display the video. If it does not work then try again but this time try to push the button/switch twice. In my truck I only have to do it once and it works fine but you get the idea.

I have the same dvd.what i did was hook the ground up from the deck too the ground wire too the car and get the yello wire which should be e brake wire.hook that up too ground wire up 2 the car ground and deck ground.after that u have too kinda play with the right side botton push it in 2 time real fast too engage e brake/

Srfse

Conecta el cable de color rosa a la masa del auto o al negatico.... y chau problema

Yess it works i used a 3 way switch and it works great

Can the Ipod play movies thru the deck. Also put movies on the screen from ipod. thanks

Chrysler01 has the right idea. It's the exact same thing my cousin done with his Dual xdvd700....with the toggle switch...then cut it off....on....off....on.....again before each use...usually have to do it twice....it works!

How do you play dvd -r or plus r in this headunit cant figuer it out

I installed one of these radios today and all we had to do was use a 3 pole switch 1gnd 2acc 3pwr run gnd to a good ground run acc to the yellow/blue wire and the pwr to a power source. Then when you turn on your car turn the switch on...off...on...off wait a sec with every change and when you turn it off the last time and wait for like 5 seconds it will show video till you turn off the car agian.

AQUIEN PUEDAINTERESAR TENGO UN XDVD700 Y TENGO PROBLEMAS CON EL SISTEMA MECANICO DEL DVD NESECITO ARGUN DIAGRAMA SOLO DE ESA PARTE LO BREGARON Y NO ESTA EN TIEMPO

GRACIAS DE ANTEMANO ATT CAMACHO [email protected]

Ground the line, wait 1 second
Unground the line, wait 1 second
Ground the line, wait 6 seconds

..video

I installed a toggle switch that you can do it with quite easily.

Splice the yellow wire with the blue stripe into the same black ground wire the unit is grounded to.