Question about Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Wf540g flashing lights power and half load

The maching starts then stops after fue seconds with power light and half load lights flashing hope someone can help please

Posted by on

  • Anonymous Jan 17, 2009

    i have the same problem i will try getting a new computer board and fitting it to see weather thatl work

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a hotpoint wf440 with the same fault. An engineer called and said it was a defective computer board. He said it would cost £90 for the part. I found it at http://www.emwelec.co.uk/ for under £50. I have ordered it and will fit when it arrives and let you know!!

Posted on Dec 03, 2006

  • Richard Pierce Dec 07, 2006

    Fitted the computer board and it all worked fine.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Elba washing maching wa65tm stops at rinse


have u got a rinse hold switched on.this is to keep clothes from getting creases it holds until someone tells it to complete cyle

Nov 20, 2015 | Fisher Paykel Fisher & Paykel Elba 3.7 cu...

1 Answer

Why is my Sony VAIO VPCEB33FM green power light flashing?


It won't be the cpu. If it was, nothing would happen. I would look for a GPU issue, possible over heat.

Jan 01, 2015 | Sony Vaio Vpceb33fm

1 Answer

My zanussi zwg 6141p washing machine is calling water at start of cycle but is not going into drawer to swill out detergent , is also stopping half way with the green light on the start button flashin


Some appliances malfunction can be displayed in hexadecimal or in binary code.
So your device is defective and shows you what's wrong. You have to count how many times flashes red light and how many times flashes green light. Red light shows the first error number and green light the second error number.
For example: you forgot to close the door and you started washing machine. After some time (timeout) will generate an alarm. Four times will flash red light and once the green light which means error code " E41 " or "Open door"
" E20 " means "No drain water"
" E10 " means "No fill up water"


Dado

Sep 08, 2014 | Zanussi Washing Machines

1 Answer

Flashing lights and machine stops operating


the water pump stuck for some reason try to open and check it if it is clean and there no residue arround the turbine
if noting there the pump should be changed

Jan 02, 2014 | Hotpoint Aquarius WMA56 Front Load Washer

1 Answer

My mitsubishi flashes a red light what does that mean


Red light is usually lamp indicator---may be time to replace the lamp--they have a 2000 hour life span except for generic ones which last half that long----when was lamp last replaced? also the set does have a self check:

After you turn on the set, and get the regular red blinky lights, hold down the Device and Menu buttons together for about 5 seconds.
The Power light will start to flash in a two digit sequence.
For example, 3 flashes, then 7 flashes = 37.
Here are the error codes, and the corresponding problem:
12 = No error detected, check power supply.
32 = Lamp Cover is open.
33 = Air filter cover is open.
34 = Lamp abnormality
36 = Light Engine (DMD or Lamp Fan stopped)
37 = Exhaust or Lamp Ballast Fan stopped
38 = Lamp Temperature High
39 = DMD Temperature High
41 = Short is detected
44 = DVI cable between FMT and Engine disconnected

Oct 30, 2012 | Mitsubishi WD-60737 60 in. HDTV

2 Answers

Kenmore washer model #21302 lock on light is flashing, will not start


Kenmore top load washer 21302, the sensor light is on and the lid lock light is on with a clicking noise. What could be wrong with it and how do I fix it?

May 21, 2012 | Kenmore Washing Machines

1 Answer

What is the fuse box layout for 1998 nissan pulsar need to change a fuse but layout is all in Japanese dont know which fuse to look for . both front park lights are not working so wanted to check the...


Hi,if you know where the fues box is your half way there.
just buy a electricle screwdriver that has a light inside it with a wire that has got a crockerdile clip on the end,
put the cockerdile clip on a earth the body of the car,
then look at the fues on the top of the fues there is two little bits of metal these are where you will put the screwdriver blade to,
if yoy put the ignition on then go back to the fuesestuch one side of the fues on the little bit of metal the screwdriver should light,This is the power side,now if you tuch the screwdriver on the other bit of metal the light should come on again,if it dose the fues is ok,
if not the fues is falty(replace fues)do this to all the fueses and you will find the fues that is falty.
all the best.

Mar 20, 2011 | Nissan Pulsar Cars & Trucks

1 Answer

Installed a new ingintion switch know security light flashes and car will not start


this process will take about half an hour to doyou might want to put a battery charger on it on the low setting because if the battery dies in process u have to start over.first thing is try to start car,it might start then stall,when that happens leave the key in the on position and the security light will be flashing and it will keep doin it for 10 minutes,then it will stay on solid,when it does that turn the key off for 2 seconds then turn it to the on position anfd the light will be flashing agian for 10 minutes,then it will be on solid,then turn the key off for 2 seconds and then back on and 10 minutes later when it stops flashing this time u should be able to start it and the light should be off,hope this helps

Sep 23, 2009 | 2003 Oldsmobile Alero

2 Answers

Wil163 3 lights flash mid wash


My machine starts filling with water, then the power button and the two next to it start to flash, and the water starts to drain from the machine.

Apr 12, 2009 | Indesit WA 115 Front Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WF000 Front Load Washer Logo

Related Topics:

404 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

vince

Level 3 Expert

1216 Answers

Eric Taylor

Level 3 Expert

560 Answers

ptpumpman

Level 3 Expert

408 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...